Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1:

Illustrate briefly the any one illustration of the telecontrol system.

problem 2:

What do you understand by the remote regulation? Illustrate about remote regulation with illustrations.

problem 3:

Illustrate the attenution in optical fibbers with figures.

problem 4:

Make a distinction between step index and graded index fibbers.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911207

Have any Question? 


Related Questions in Electrical & Electronics

1 in dictionary coding if there are 60 characters in the

1. In dictionary coding, if there are 60 characters in the message, how many times is the loop in the compression algorithm iterated? Explain. 2. In dictionary coding, should all dictionary entries that are created in th ...

1 consider three equally spaced sources of strength m

1. Consider three equally spaced sources of strength m placed at (x, y) = ( a, 0),(0, 0), and (a, 0). Sketch the resulting streamline pattern. Are there any stagnation points? 2. Sketch the streamlines and potential line ...

Identify the variables associated with given problem and

Identify the variables associated with given Problem and find the dimensionless parameters. Problem The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary cas ...

Clculate the surface integral of the vector function f

Calculate the surface integral of the vector function, F = xe 1  + ye 2 , over the portion of the surface of the unit sphere, S : x 2  + y 2  + z 2  = 1, above the xy-plane, i.e., z > 0.

Load flow calculation -in the power network shown below

Load Flow Calculation - In the power network shown below, node 1 is the slack bus, where the nodal voltage is defined as (1.0∠0 o ) pu, nodes 2, 4 and 5 are load buses, and node 3 is a generator bus where the voltage mag ...

1 how is the magnetic flux density defined in terms of

1. How is the magnetic flux density defined in terms of force on a current element? 2. How is the magnetic flux density defined in terms of force on a moving charge? 3. What are the units of the magnetic flux density? 4. ...

Power mosfet breakdown voltage 800v must conduct 10a when

power mosfet breakdown voltage 800v must conduct 10A when on with a maximum on state voltage 4v.If the current density in the mosfet must be limited to 200A/cm,estimate the conduxting area

1 implement the 2-to-4 decoder using 7404 not an 7808 and

1. Implement the 2-to-4 decoder using 7404 (NOT) an 7808 (AND) chips on your breadboard. 2. Implement the 2-to-4 decoder circuit with a 74139 chip on your breadboard. 3. Implement a 1-to-2 decoder in Logisim. Implement t ...

1 define the parts of flow specification in intserv2

1. Define the parts of flow specification in IntServ. 2. Distinguish between guaranteed services and controlled-load services in IntServ. 3. IntServ is normally called a destination-based service. Explain the reason. 4. ...

Determine the head loss between stations 1 and 2 in

Determine the head loss between stations (1) and (2) in Problem. Problem:- Oil (sp. gr. = 0.8) flows smoothly through the circular reducing section shown at 3 ft 3  /s. If the entering and leaving velocity profiles are u ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro