Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

Illustrate out why acid iron is also called haematite iron or sweedish iron.

problem 2:

Illustrate what Thomas iron is.

problem 3:

What do you understand by the steel scrap? Illustrate about various types of steel scraps employed in steel making.

problem 4:

What are the benefits of twin-hearth furnace procedure of steel making?

problem 5:

prepare down a short note on future of continuous steel making process.

problem 6:

Illustrate about the mechanism of oxygen transfer in open hearth furnace steel making process.

problem 7:

With the use of a appropriate sketch, illustrate about tilting open-hearth furnace.

problem 8:

prepare down the advantages and drawbacks of furnace.

problem 9:

Illustrate out the term bottom teeming.

problem 10:

What are the advantages and drawbacks of bottom teeming?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911259

Have any Question? 


Related Questions in Mechanical Engineering

A for the system of fig 347 the resistance of each line

a. For the system of Fig. 3.47, the resistance of each line cannot exceed 0.006 Ω, and the maximum current drawn by the load is 110 A. What gage wire should be used? b. Repeat (a) for a maximum resistance of 0.003 Ω, d = ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

This atomic force microscope probe is a silicon beam and

This atomic force microscope probe is a silicon beam and tip. The beam is 40 µm wide, 4 µm thick, and 130 µm long. The tip is set back 15 µm from the end of the cantilever. The deflection of the tip is 1 µm for every 42 ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

A sample of propane c3h8 is placed in a closed vessel

A sample of propane (C 3 H 8 ) is placed in a closed vessel together with an amount of O 2 that is 2.15 times the amount needed to completely oxidize the propane to CO 2 and H 2 O at constant temperature. Calculate the m ...

A sample of he ions is prepared at a temperature of 298 k

A sample of He + ions is prepared at a temperature of 298 K and a density of 2.0 # 10 10 cm -3 . Because these are ions, magnetic ields may be used to trap those ions with kinetic energy less than some threshold value et ...

A 10 hp y-connected 60 hz 380 v three-phase induction

A 10 hp, Y-connected, 60 Hz, 380 V, three-phase induction generator is used to drive a small micropower plant. The generator's load is 500 W for a 4 A line current at 1740 rpm. The rotor resistance is 4.56 Ω at 75°C. The ...

Part 1- heat1 the is used to express absolute temperatures

Part 1- Heat 1. The _______ is used to express absolute temperatures in the English system of measurement. A. Rankine scale B. Celsius scale C. Kelvin scale D. Fahrenheit scale 2. A silver bar 0.125 meter long is subject ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen