Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

prepare down comprehensive notes on ionic theory of slags.

problem 2:

Illustrate the necessary situations required for effective desulphurization and dephosphorization in steel making processes.

problem 3:

Illustrate in detail the crucible procedure of steel making.

problem 4:

Illustrate about the crucible employed in crucible process of steel making

problem 5:

Illustrate out the quality and properties of steel produced by crucible process.

problem 6:

Illustrate the various reactions taking place in oxidizing and reducing periods in electric arc furnace of steel making.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911261

Have any Question? 


Related Questions in Mechanical Engineering

A nut having an effective length of 2 in and a 12-16 un

A nut having an effective length of 2 in. and a 1/2-16 UN thread is snug tightened and then turned 308. How much preload will that create in the bolt? Is that an acceptable preload? Describe the typical torque-turn tight ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

Bull why do individual bolts relax a bit when first

• Why do individual bolts relax a bit when first tightened? Name several factors that can increase the relaxation ? Which will tend to loose more preload after initial tightening, a short bolt or a long bolt? • What are ...

Obtainand research literture on automotive fuel additives

Obtainand research literture on automotive fuel additives and their properties and prepare a typed 2 page report on your findings. -are they worth the money or are they a waste of time? -do they work? -how? -what is your ...

The professor took us to trip to a place and told us to

The professor took us to trip to a place and told us to write 3 pages about What do i think about the trip? What was interesting? What is my impression ? https://www.dropbox.com/s/29un7cfm1jify5v/2016-11-26_20-42_0.rar?d ...

1 what is a stress-strain diagram2 explain the difference

1. What is a stress-strain diagram? 2. Explain the difference between elastic limit and proportional limit. 3. Explain the difference between the concepts of yield point and yield stress. 4. What is offset strain? IS. Ho ...

The doctoral candidate phd research is entitled a critical

The Doctoral Candidate PhD research is entitled "A critical Investigation of Risk Management Practices Influence on the Pharmaceutical Supply Chain Performance" The focus of this dissertation is thus on the risk manageme ...

1 using matlabsimulinkreg write a computer program to

1. Using MATLAB/Simulink®, write a computer program to represent the SEIG in its transient state. 2. Explain why an IG cannot self-excite under the following conditions: (1) no residual magnetism, (2) after too much indu ...

We want to tighten an astm a193 bolt having 4-8 un threads

We want to tighten an ASTM A193 bolt having 4-8 UN threads and a yield strength of 96 ksi. The effective length of its body, Lbe, is 12 in.; that of its threads, Lse, is 4 in. We're going to control the buildup of preloa ...

The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro