Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

prepare down the different techniques for hydrogen storage? Illustrate out their advantages and drawbacks.

problem 2:

What do you understand by the term electrolysis? Illustrate out the more popular technique of hydrogen production.

problem 3:

Illustrate out the lead – acid battery developments for automobile applications.

problem 4:

Illustrate out the principle and operation of sodium –sulphur battery.

problem 5:

Illustrate out the impact of Electric cars usage in urban areas on air quality as compared to convention vehicles.

problem 6:

prepare down the advantages and disadvantages a gas turbine plant in automotive applications.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911001

Have any Question? 


Related Questions in Mechanical Engineering

A rigid vessel of volume 0400 m3 containing h2 at 2125degc

A rigid vessel of volume 0.400 m3 containing H2 at 21.25°C and a pressure of 715 X 10 3 Pa is connected to a second rigid vessel of volume 0.750 m 3 containing Ar at 30.15°C at a pressure of 203 X 10 3 Pa. A valve separa ...

For a deck supports of length 325 m are proposed to be

For a deck, supports of length 3.25 m are proposed to be built from aluminum with a Young's modulus of 72 GPa and a yield stress of 480 MPa. A cylindrical design is proposed with outer diameter d = 100 mm and wall thickn ...

Use castiglianos second theorem to determine the tip

Use Castigliano's second theorem to determine the tip deflection of this cantilever with a length L, a constant E I, and a linearly increasing load with a maximum force/length q0. Confirm your result using Table 9.1.

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

Part 1- heat1 the is used to express absolute temperatures

Part 1- Heat 1. The _______ is used to express absolute temperatures in the English system of measurement. A. Rankine scale B. Celsius scale C. Kelvin scale D. Fahrenheit scale 2. A silver bar 0.125 meter long is subject ...

Two small cubes of equal size but made of different

Two small cubes of equal size but made of different materials are stacked (as shown in the figure below), so they just fit between two rigid surfaces. The bottom cube is subjected to a uniform pressure p on each of its e ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

Question 1derive an expression for the velocity vector of

Question 1: Derive an expression for the velocity vector of the collar D, N V D. The upper arm (B) rotates about a horizontal axis ( nˆ x ) at a rate q · 1 The lower arm (C) Rotates about the longitudinal axis of B (bˆ z ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen