+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1:

Discuss any three types of car body with appropriate diagram.

problem 2:

Illustrate out the term visibility and discuss in detail about techniques for enhancing visibility in cars.

problem 3:

Illustrate out the different body optimization methods for providing minimum drag in vehicles.

problem 4:

Critically discuss the different types of forces and moments act on the vehicle body with neat diagram.

problem 5:

Illustrate out with an appropriate sketch the construction of mini bus, double Decker and articulated type bus body.

problem 6:

prepare down the types of frame construction employed in body construction and discuss in detail.

problem 7:

Illustrate out with the use of appropriate sketch of the design factors involved in driver cab design with a neat sketch.

problem 8:

Illustrate out the different types of light commercial vehicle bodies with appropriate sketches.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M912608

Have any Question?

## Related Questions in Mechanical Engineering

### Assignmentin mse 2010 we talk about several general classes

Assignment In MSE 2010 we talk about several general classes of materials: metals, polymers, ceramics, glasses and composites. We know that these are just the basic categories and we've discussed several specific example ...

### A linear spring k is to be designed to stop a 20-mg

a linear spring k is to be designed to stop a 20-mg railroad car traveling at 8km/h within 400 mm after impact. Find the smallest value of k that will produce the desired result.

### Please reference any source of outside information as

Please reference any source of outside information as needed to answer these questions. 1. In a frozen food plant, atmospheric air is to go through a pre-cooler to be partially dehydrated so that during its passage throu ...

### Use castiglianos second theorem to determine the tip

Use Castigliano's second theorem to determine the tip deflection of this cantilever with a length L, a constant E I, and a linearly increasing load with a maximum force/length q0. Confirm your result using Table 9.1.

### 1 discuss the four best-known practical methods of

1. Discuss the four best-known practical methods of generating residual magnetism. 2. Discuss the advantages of a matrix partition to represent the transient state of an aggregation of SEIGs. 3. Using the state variable ...

### If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

### When choosing a bolting material we must consider its

When choosing a bolting material we must consider its affect on the clamping force to be created by those bolts in service. Name two important aspects of the clamping force which will be affected, in part at least, by th ...

### Task to identify research and present in both written and

Task: To identify, research, and present (in both written and oral formats) a topic in engineering that is currently the focus of ongoing (within the past 5 years) research, investigation, and/or development.The topic mu ...

### A for the system of fig 347 the resistance of each line

a. For the system of Fig. 3.47, the resistance of each line cannot exceed 0.006 Ω, and the maximum current drawn by the load is 110 A. What gage wire should be used? b. Repeat (a) for a maximum resistance of 0.003 Ω, d = ...

### Problem -an aluminum extrusion was created in the shape at

Problem - An aluminum extrusion was created in the shape at the right as shown with the origin at the lower left corner. Show all work in finding the centroid (4). Find moments of inertia with respect to the x and y axes ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro