Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

prepare down the common format which is employed by the RP systems. Illustrate the format and describe with an ex.

problem 2:

Critically discuss the process flow of 3D System Sterolithography Apparatus. Illustrate its advantages and drawbacks.

problem 3:

Illustrate out the Working Principles of the Selective Laser Sintering. Discuss its Merits and Demerits.

problem 4:

Demonstrate with the use of neat sketch about the Laminated Object Manufacturing Process and illustrate its applications.

problem 5:

Illustrate out the application of the rapid prototyping in the Aerospace Industries.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912500

Have any Question? 


Related Questions in Mechanical Engineering

A water jet pump has an area ajnbsp 006 ft2nbspand a jet

A water jet pump has an area A j  = 0:06 ft 2  and a jet velocity v j  = 90 fps, which entrains a secondary stream of water having a velocity v s  = 10 fps in a constant-area pipe of total area A = 0.6 ft 2 . At section ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

1 an equation linking water density and pressure iswhere

1. An equation linking water density and pressure is where the pressure is in atmospheres and B =3000 atm. Determine the pressure in psi required to increase water density by 1% above its nominal value. 2. What pressure ...

A linear spring k is to be designed to stop a 20-mg

a linear spring k is to be designed to stop a 20-mg railroad car traveling at 8km/h within 400 mm after impact. Find the smallest value of k that will produce the desired result.

Gas turbine engines are mostly seen in aircraft while

Gas turbine engines are mostly seen in aircraft, while piston combustion engines are mostly seen in ground vehicles. Which advantages and disadvantages of these engines have caused them to be favorable for their respecti ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro