Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1:

Illustrate out the Numerical Aperture of a fibre.

problem 2:

Illustrate out the term Mode-field diameter

problem 3:

prepare down the types of bends which can be subjected to a fibre?

problem 4:

Make a distinction between splice and connector.

problem 5:

Illustrate out internal quantum efficiency of a LED

problem 6:

Discuss the properties of Laser light.

problem 7:

prepare down the different factors which determine the response time of photo detector?

problem 8:

Illustrate the performance of APD and PIN diode.

problem 9:

prepare down the Lasers that are used in Gynaecology.

problem 10:

What are the diseases which can be cured by Lasers in ophthalmology?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913081

Have any Question? 


Related Questions in Electrical & Electronics

1 what is the propagation vector interpret the significance

1. What is the propagation vector? Interpret the significance of its magnitude and direction. 2. Discuss how the phase constants along the coordinate axes are less than the phase constant along the direction of propagati ...

1 in polar coordinates show that2 determine the fluid

1. In polar coordinates, show that 2. Determine the fluid rotation at a point in polar coordinates, using the method illustrated in given figure.

1 discuss briefly the motional emf concept2 what is lenzs

1. Discuss briefly the motional emf concept. 2. What is Lenz's law? 3. How would you orient a loop antenna in order to obtain maximum signal from an incident electromagnetic wave which has its magnetic field linearly pol ...

An output interface in a switch is designed using the leaky

An output interface in a switch is designed using the leaky bucket algorithm to send 8000 bytes/s (tick). If the following frames are received in sequence, show the frames that are sent during each second. ? Frames 1, 2, ...

An ideal transformer has a 150-turn primary and 750-turn

An ideal transformer has a 150-turn primary and 750-turn secondary. The primary is connected to a 240-V, 50-Hz source. The secondary winding supplies a load of 4 A at a lagging power factor (pf ) of 0.8. Determine (a) th ...

The power output of a hydraulic turbine depends on the

The power output of a hydraulic turbine depends on the diameter D of the turbine, the density ρ of water, the height H of water surface above the turbine, the gravitational acceleration g, the angular velocity ω of the t ...

Explain the reasoning in the application tiger woods rents

Explain the reasoning in the application "Tiger Woods' Rents" as to why Tiger Woods was able to capture essentially all the rents from some companies but not from others.

The maximum pitching moment that is developed by the water

The maximum pitching moment that is developed by the water on a flying boat as it lands is noted as cmax The following are the variables involved in this action: a = angle made by flight path of plane with horizontal, β ...

Consider a pv array charging batteries for an off-the-grid

Consider a PV array charging batteries for an off-the-grid, stand-alone system near Boulder, Colorado You plan to run everything in the house on 120 V ac. a. Suppose the load is estimated to consist of the following 120 ...

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro