Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

How the bus bodies categorized? Illustrate the design and construction of integral bus.

problem 2:

Mention the advantages and drawbacks of the integral bus.

problem 3:

prepare down the ergonomical considerations adapted in seat design of automobiles?

problem 4:

Acquire a relationship between forces on an airfoil based on wind axis and body axis. How can you make employ of dimensional analysis to acquire these forces in terms of physical parameters available to you?

problem 5:

A compressor and electric motor are mounted on the undamped vibration isolation platform and create the static deflection of 10 mm. Compute:

(a) The natural frequency of assembly;

(b) i. The transmissibility; and

ii. The percentage isolation if the working compressor/motor generates a forcing frequency of 30 Hz.

iii. The lowest forcing frequency for which the isolation is 95%.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M910934

Have any Question? 


Related Questions in Mechanical Engineering

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

The demand for a certain product is a linear function of

The demand for a certain product is a linear function of the price. The sales of the product for three different prices are given in the following table Find the least squares regression line and estimate the demand when ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

Name several ways by which the loss of initial preload can

Name several ways by which the loss of initial preload can be reduced ? Roughly how much embedment relaxation could we expect from new parts used in a non-gasketed, steel joint? Define elastic interactions. How can elast ...

A prototype bolt shaft assume a uniform cylinder that is to

A prototype bolt shaft (assume a uniform cylinder) that is to be loaded in tension is made of a stainless steel with a yield strength of 450 MPa and has a safety factor of 3 with respect to yielding for the maximum allow ...

1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

A gas sample is known to be a mixture of ethane and butane

A gas sample is known to be a mixture of ethane and butane. A bulb having a 230.0 cm 3 capacity is filled with the gas to a pressure of 97.5 X 10 3 Pa at 23.1°C. If the mass of the gas in the bulb is 0.3554 g, what is th ...

If superman has a mass of 100 kg on his birth planet

If Superman has a mass of 100 kg on his birth planet Krypton, where the acceleration of gravity is 25 m/s2, determine (a) his weight on Krypton, in N, and (b) his mass, in kg, and weight, in N, on Earth whereg5 9.81 m/s2 ...

Rework given problem if the plates are circular and have

Rework given Problem. if the plates are circular and have radius L. Problem :- Two very long parallel plates of length 2L are separated a distance b. The upper plate moves downward at a constant rate V. A fluid fills the ...

The average heat evolved by the oxidation of foodstuffs in

The average heat evolved by the oxidation of foodstuffs in an average adult per hour per kilogram of body weight is 7.20 kJ kg-1 hr -1 . Assume the weight of an average adult is 62.0 kg. Suppose the total heat evolved by ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro