Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe the purpose of the I/O instructions IN and OUT.

2) prepare down the difference between the shift and rotate instructions?

3) How many address lines in a 4096 x 8 EPROM CHIP?

4) prepare down the control signals that are used for DMA operation.

5) What do you mean by wait state?

6) prepare down the four instructions that control the interrupt structure of the 8085 microprocessor.

7) What do you mean by polling?

8) Describe interrupt in detail with suitable ex.

9) Describe priority interrupts of 8085.

10) What do you mean by a microcomputer?

11) What is the signal classification of 8085?

12) prepare down the operations that are performed on data in 8085?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910916

Have any Question? 


Related Questions in Electrical & Electronics

1 what is an anisotropic dielectric material2 when can an

1. What is an anisotropic dielectric material? 2. When can an effective permittivity be defined for an anisotropic dielectric material? 3. Briefly describe the phenomenon of magnetization. 4. What is a magnetic dipole? H ...

It is desired to strip trichloroethylene o2hcl3 from a

It is desired to strip trichloroethylene, O 2 HCl 3 , from a contaminated groundwater stream. The groundwater, which can be treated as a dilute water stream, will be fed to the top of the tower operating at 288 K and 1.0 ...

1 in one-dimensional dct if n 1 the matrix transformation

1. In one-dimensional DCT, if N = 1, the matrix transformation is changed to simple multiplication. In other words, M = T × p, in which T, p, and M are numbers (scalar value) instead of matrices. What is the value of T i ...

Repeat problem with the elastic constants of the plastic

Repeat Problem with the elastic constants of the plastic defined as E = 10 GPa and ν = 0.485. Problem:- A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions ...

Assignment projecttitle design of control

Assignment: Project Title: Design of Control Systems Problem: Design a closed-loop controller for a servo system (motor) with tachometer feedback. The output; c(t), corresponds to the position of the motor, while the tac ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

1 why is it necessary to have the minus sign associated

1. Why is it necessary to have the minus sign associated with the time rate of increase of magnetic flux on the right side of Faraday's law? 2. What is electromotive force? 3. What are the different ways in which an emf ...

1 what is the basis behind the construction of the smith

1. What is the basis behind the construction of the Smith Chart? How does the Smith Chart simplify the solution of transmission-line problems? 2. Briefly discuss the mapping of the normalized line impedances from the com ...

Discretize the continuous-time system with transfer

Discretize the continuous-time system with transfer function H(s) = (s + 10 )/s with use of the bilinear (Tustin) approximation method. Verify your result by converting the computed discrete-time system to continuous-tim ...

1 explain the term internal inductance2 what is meant by

1. Explain the term internal inductance. 2. What is meant by the quasistatic extension of the static field in a physical structure? 3. Outline the steps involved in the electroquasistatic field analysis of a parallel pla ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen