+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

problem 1: Draw the projections of the given considering the Reference Line X-Y to be the same. You might keep the distance between the projectors equal to 30 mm.

a) Point ‘A’ 50 mm above H.P. and 60 mm behind V.P.
b) Point ‘B’ 45 mm below H.P. and on V.P.

problem 2: Draw the projection of a line which is 65 mm long and its one end is in HP at a point 15 mm in front of the VP. The other end is in the third quadrant. The line is inclined at 60° to HP and 30° to VP. Draw the projections of line.

problem 3: A pentagonal sheet having all edges equal in length is placed with one edge parallel to HP. The surface of the sheet is inclined at 30° to HP and parallel to VP. If each side of sheet is 50 mm, draw its projections.

problem 4: Given figure illustrated below shows the top-view and front of a cylinder, cut by a Sections-plane V.T. Show its Sectional-Top-View.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M92687

Have any Question?

## Related Questions in Mechanical Engineering

### 1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

### The top figure shows a diagram of the bones and biceps

The top figure shows a diagram of the bones and biceps muscle of a person's arm supporting a mass. The lower figure shows a biomechanical model of the arm, in which the biceps muscle AB is represented by a bar with pin s ...

### A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

### On a certain day the barometric pressure at sea level is

On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 70°F. The pressure gage in an airplane in flight indicates a pressure of 10.6 psia, and the temperature gage shows the air temp ...

### In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

### A mixture of 210 x 10-3 g of o2 388 x 10-3 mol of n2 and

A mixture of 2.10 X 10 -3 g of O2 3.88 X 10-3 mol of N 2 . And 5.25 X 10 -3 molecules of CO are placed into a vessel of volume 5.25 L at 12.5°C. a. Calculate the total pressure in the vessel. b. Calculate the mole fracti ...

### A solid circular shaft of 40 mm diameter is to be replaced

A solid circular shaft of 40 mm diameter is to be replaced by a hollow circular tube. If the outside diameter of the tube is limited to 60 mm, what must be the thickness of the tube for the same linearly elastic material ...

### 1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

### Determme the dimensions in both the flt system anltlthe mlt

Determme the dimensions, in both the FLT system an (a) the product of force times acceleration, (b) the product of force times velocity divided by area. and (c) momentum divided by volume

### Problem -a consider a one-component system consisting of

Problem - a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liqui ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro