Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) A) For Pt at 20 C compute how many unit cells there are per cubic meter.

B) How many total interstitial sites are there in one cubic meter of Pt at 20 C Which will you expect to be more probable in Pt at 20 C, vacancy diffusion or interstitial diffusion?

problem2) The 44-kg crate is hoisted up 300 inclineby the pulley system and motor M. If crate starts fromrest and, by constant acceleration, attains a speed of 4 m/s after traveling 8m along the plane, find pout the power that should be supplied to the motor at the instant the crate has moved 8m. Neglect friction along the plane. The motor has an efficiency? = 0.76.

170_Pulley system.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93949

Have any Question? 


Related Questions in Mechanical Engineering

Chemistry buildings built to code require a great deal of

Chemistry buildings built to code require a great deal of ventilation, which necessitates a delicate air-handling system to balance the air lowing into the building and the air lowing out. For example, if the air low out ...

Problem -a piston at one end of a gas filled circular tube

Problem - A piston at one end of a gas filled circular tube of area S oscillates with real-valued velocity: U p (t) = U 1 cos(ω 1 t) + U 2 sin(ω 2 t) Note that two oscillation frequencies are present. The other end of th ...

1 estimate the viscosity of nitrogen at 175 k using given

1. Estimate the viscosity of nitrogen at 175 K using given equation. 2. Calculate the viscosity of oxygen at 350°K and compare with the value given in Appendix I. 3. What is the percentage change in the viscosity of wate ...

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

A sample of propane c3h8 is placed in a closed vessel

A sample of propane (C 3 H 8 ) is placed in a closed vessel together with an amount of O 2 that is 2.15 times the amount needed to completely oxidize the propane to CO 2 and H 2 O at constant temperature. Calculate the m ...

Select a topic on the discussion board discussion section

Select a topic on the discussion board (DISCUSSION section of blackboard) There are four categories of topics; organizations, testing methods, elements and specialty components. Each has something to do with industrial m ...

Bull why do individual bolts relax a bit when first

• Why do individual bolts relax a bit when first tightened? Name several factors that can increase the relaxation ? Which will tend to loose more preload after initial tightening, a short bolt or a long bolt? • What are ...

Calculate the first-order correction to the energy of a

Calculate the first-order correction to the energy of a ground-state harmonic oscillator subject to an anharmonic potential of the form ax 3 +bx 4 where a and b are small (anharmonicity) constants. Consider the three cas ...

In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

List three ways to control preload directly what are the

List three ways to control preload directly ? What are the advantages of a bonded ultrasonic transducer? What is sometimes cited as a disadvantage? Can torque be used to tighten a 6 in. diameter bolt? If not, why not? Na ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen