Ask Question, Ask an Expert

+61-413 786 465

info@mywordsolution.com

Ask Mechanical Engineering Expert

Find the magnitude of the angular acceleration of system:

A homogeneous sphere having a mass of 100 kg is associated to a slender rod having a mass of 20 kg. In the horizontal position, the angular speed of the system is 8 rad/sec. calculate the magnitude of the angular acceleration of the system and the reaction at O on the rod.

Solution

The system shall be rotating about O as shown in the figure. First let us try to locate the mass centre of the system.

∴ x¯ = (20 × 300 + 100 × 750) /120

= 675 mm .

The position of the mass centre is shown in the free body diagram in Figure (b). All the forces acting on the system are illustrated on FBD.

External forces are reactions at O, i.e. OT and ON and gravitational force mg shall be acting through the mass centre. r ω2 and r α shall be normal and tangential components of acceleration and mr ω2 and mr α are initial forces in these respective directions.

The total moment of inertia I equals the moment of inertia of the rod about its end ( 1/3) ml2  plus the transferred moment of inertia of the sphere, that means

               ( 2/5) mr 2  + md 2

where, d = 750 mm = 0.75 m

∴ I = (1/3) 20 (0.6)2  + (2/5) 100 (0.15)2  + 100 (0.75)2

= 59.55 kg m 2 .

Now apply dynamic equilibrium equations. ∑ M o  = 0 shall give us magnitude of α.

∴ ∑ M - I α = 0

∴ 120 × 9.8 × 0.675 = 59.55 α

∴ α = 13.3 rad / sec 2 .

Now, ∑ Fx = 0 . Thus, the sum of the forces on horizontal axis,

- ON + m r ω2 = 0

∴ ON = 120 × (0.675) (8)2 = 5180 N         to the left.

And,

∑ Fy = 0

- OT - mg + mr α = 0

∴ OT= mg - mr α

= 120 × 9.8 - 120 × 0.675 × 13.3

∴ OT = - 98.7 N.

Thus, direction of OT is upwards.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M9519968

Have any Question?


Related Questions in Mechanical Engineering

Expansion processes of a perfect gasassignment1 attend the

Expansion Processes of a Perfect Gas Assignment: 1. Attend the laboratory class and complete the lab tests according to the supervisor's requirement. Students will not allowed to submit their report if they do not come t ...

Assignment - machine learning for signal processingproblem

Assignment - Machine Learning for Signal Processing Problem 1: Instantaneous Source Separation 1. As you might have noticed from my long hair, I've got a rock spirit. However, for this homework I dabbled to compose a pie ...

5star questions amp answers1a define heat treatment bname

5 STAR QUESTIONS & Answers 1. A) Define Heat treatment B) Name different types of heat treatment processes C) Write any 4 purposes of Heat treatment 2. Explain various Heat treatment processes 3. A) Compare Thermo plasti ...

Fluid mechanics assignment - viscous flow in pipesq1 as

Fluid Mechanics Assignment - Viscous Flow in Pipes Q1. As shown in the figure below, water "bubbles up" 3 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-i ...

Questions -q1 a qualitative estimate of the effect of a

Questions - Q1. A qualitative estimate of the effect of a wind-tunnel contraction (Figure) on turbulent motion can be obtained by assuming that the angular momentum of eddies does not change through the contraction. Let ...

Materials behaviour from atoms to bridges assignment -

Materials Behaviour from Atoms to Bridges Assignment - Distributed loads and static equilibrium (Please note: you should show your steps with necessary figures) Q1. Two beam sections are jointed at C and supported at A b ...

Force exerted by jet on moving cart1 you need to determine

Force Exerted By Jet On Moving cart. 1. You need to determine the velocity of water that comes out from the nozzle of this system. need the equation please formulate the equation. 2. This water will strike a small cart a ...

Alocate ten minutes for the presentationuse audio visual

Allocate ten minutes for the presentation Use audio / visual / technological supports / aids where appropriate Use a minimum of 3 properly referenced articles. THEMES PRESENTATION TOPIC MEMORY Discuss the three learning ...

Problem -a long pipe od 1413 mm id 1318 mm kp 20 wmk

Problem - A long pipe (OD = 141.3 mm, ID =131.8 mm, k p = 20 W/m.K) supplies hot pressurized liquid water at 400 K to a heater in a factory. The pipe has an insulation thickness of 100 mm. A new efficient heater replaces ...

Life cycle assessmentfor your chosen service eg white board

LIFE CYCLE ASSESSMENT For your chosen service (e.g. white board markers), identify two alternatives of getting the service (e.g. brand A, brand B). Choose the most environmentally friendly option by conducting life cycle ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Why might a bank avoid the use of interest rate swaps even

Why might a bank avoid the use of interest rate swaps, even when the institution is exposed to significant interest rate

Describe the difference between zero coupon bonds and

Describe the difference between zero coupon bonds and coupon bonds. Under what conditions will a coupon bond sell at a p

Compute the present value of an annuity of 880 per year

Compute the present value of an annuity of $ 880 per year for 16 years, given a discount rate of 6 percent per annum. As

Compute the present value of an 1150 payment made in ten

Compute the present value of an $1,150 payment made in ten years when the discount rate is 12 percent. (Do not round int

Compute the present value of an annuity of 699 per year

Compute the present value of an annuity of $ 699 per year for 19 years, given a discount rate of 6 percent per annum. As