Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) prepare detailed notes on Graphics objects and Graphics properties. prepare down a program for transfer function given by using Z-N PI controller setting. G(s)=1/(S+1)3. Distinguish between simulink and M-file with a suitable ex. Find out the PID controller parameters by using C-C method and design simulink diagram for any system.

problem 2) prepare down the different kinds of Evaluation rules. prepare down the different software support Numerical  programming. prepare down a program for measuring voltages by using LabVIEW. prepare down the commands which are used in SPICE programming.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913891

Have any Question? 


Related Questions in Electrical & Electronics

It is desired to strip trichloroethylene o2hcl3 from a

It is desired to strip trichloroethylene, O 2 HCl 3 , from a contaminated groundwater stream. The groundwater, which can be treated as a dilute water stream, will be fed to the top of the tower operating at 288 K and 1.0 ...

1 the stream function for an incompressible two dimensional

1. The stream function for an incompressible, two dimensional flow field is For this flow field, sketch several streamlines. 2. A line vortex of strength K at (x, y) = (0, a) is combined with opposite strength vortex at ...

1 what is the direction of the magnetic field for a uniform

1. What is the direction of the magnetic field for a uniform plane wave having its electric field in the positive z-direction and propagating in the positive x-direction? 2. What is intrinsic impedance? What is its value ...

A discuss asymptotic and bibo stabilities for the systems

a. Discuss asymptotic and BIBO stabilities for the systems described by the following transfer functions assuming that the systems are controllable and observable: b. Repeat part (a) for systems described by the followin ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

1 in transform coding show that a receiver that receives an

1. In transform coding, show that a receiver that receives an M matrix can create the original p matrix. 2. Calculate the T matrix for DCT when N = 1, N = 2, N = 4, and N = 8. 3. Using one-dimensional DCT encoding, calcu ...

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

Consider two bar elements under a force at the tip using

Consider two bar elements under a force at the tip. Using the displacement controlled method, plot the load-displacement curve (F vs. u 2  and u 3 ). Increase the tip displacement u 3  up to 1.0 m by ten equal increments ...

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

1 what is the brewster angle what is the polarization of

1. What is the Brewster angle? What is the polarization of the reflected wave for an elliptically polarized wave incident on a dielectric interface at the Brewster angle? Discuss an application of the Brewster angle effe ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro