Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

A pressure vessel needs an internal diameter of 1.5m and will generally contain air at 30bar. For safety, the maximum tensile stress in the material to be employed must not exceed 250MN/m2 at a pressure of 60bar.

Q1. Find out the minimum acceptable wall thickness by using thin cylinder theory.

Q2. Find out the minimum acceptable wall thickness by using thick cylinder simulation software.

Q3. Comment on the importance of any difference.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M99724

Have any Question? 


Related Questions in Mechanical Engineering

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

For the state of stress given in problem 517 determinea the

For the state of stress given in Problem 5.17, determine a. the maximum shear stress b. the normal stresses on the plane of maximum shear stress c. the normal and shear stresses after the element has been rotated through ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

For the experimental pump data given belowqflow rate

For the experimental pump data given below: Q F low Rat e ( ???? /s) ???? Total Pressure (kPa) P IN Shaft power (kW) 0.0000 504.82 1.190 0.0004 481.50 1.318 0.0008 476.70 1.573 0.0012 471.50 1.828 0.0017 461.00 2.083 0.0 ...

The total pressure of a mixture of oxygen and hydrogen is

The total pressure of a mixture of oxygen and hydrogen is 1.65 atm. The mixture is ignited and the water is removed. The remaining gas is pure hydrogen and exerts a pressure of 0.190 atm when measured at the same values ...

In adiabatic demagnetization we use a magnetic ield to

In adiabatic demagnetization, we use a magnetic ield to couple away almost all of the residual energy of a crystal that has been cooled to 2.2 K by liquid helium. (We can get below the normal boiling point of liquid heli ...

1 estimate the viscosity of nitrogen at 175 k using given

1. Estimate the viscosity of nitrogen at 175 K using given equation. 2. Calculate the viscosity of oxygen at 350°K and compare with the value given in Appendix I. 3. What is the percentage change in the viscosity of wate ...

Introductionemployers are constantly asking for engineering

Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers need to be creative and innovative. They have to ...

Now consider a second joint of the same material width and

Now consider a second joint of the same material, width and thickness as the joint in problem 4 above but eccentrically loaded. This time, however, the line of action of the external load is 0.563 in. removed from the ce ...

The demand for a certain product is a linear function of

The demand for a certain product is a linear function of the price. The sales of the product for three different prices are given in the following table Find the least squares regression line and estimate the demand when ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro