Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1.  FIGURE shows a pneumatic circuit diagram used for air supply and exhaust in an automatic control system.

(a) Name all symbols (including pipelines) used in the system.
(b) Number the ports of each DCV.
(c) Classify the sections of the components in the circuit.
(d) State how the system works.
(e) State the functions of valves 1 and 2.

1363_pneumetic circuit diagram.jpg

2. FIGURE shows a pneumatic circuit in which four actuators are controlled.

(a) state the sequence in which the cylinders operate on the operation of the start valve.
(b) show, with the aid of a schematic diagram, how an electronis controller could be included in the circuit to control the sequence of cylinder operations.

1592_pneumetic circuit with actuators.jpg

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M942

Have any Question? 


Related Questions in Mechanical Engineering

A w10 times 45 beam is made of structural steel and used as

A W10 × 45 beam is made of structural steel and used as a column with a length 15 ft. If its ends are fixed, can the column support the critical load without yielding? (Thedesignation W10 × 45 provides specifications abo ...

If the kansas city building code specified that a floor

If the Kansas City Building Code specified that a floor structure must support a live load of 4.79 kPa (100 psf), and if the walkway length L = 9.1 m = 30.0 ft and width b = 2 m = 6.56 ft, what contribution is made to th ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

1 according to the equipartition principle what is the

1. According to the equipartition principle, what is the overall energy in J of one mole of water at 1000 K if translational, rotational, and vibrational degrees of freedom are considered? 2. How many equipartition degre ...

Define the endurance limit of a bolt which is greater the

Define the endurance limit of a bolt ? Which is greater, the static yield strength or the endurance limit of the bolt? When will an increase in preload increase fatigue life? When will an increase in preload decrease fat ...

The jet pump injects water at v1nbsp 40 ms through a 76 cm

The jet pump injects water at V 1  = 40 m/s through a 7.6 cm pipe and entrains a secondary flow of water V 2  = 3 m/s in the annular region around the small pipe. The two flows become fully mixed downstream, where V 3  i ...

As discussed in section 11 new parameters are oten born out

As discussed in Section 1.1, new parameters are oten born out of the need to explain inconsistencies between experimental results and prevailing theory. In physics, mass is the property that determines the magnitude of t ...

Two very long parallel plates of length 2l are separated a

Two very long parallel plates of length 2L are separated a distance b. The upper plate moves downward at a constant rate V. A fluid fills the space between the plates. Fluid is squeezed out between the plates. Determine ...

Define nut dilation why can it be a problemcompute the

Define nut dilation. Why can it be a problem? Compute the approximate thermal expansion of a 1=2-13 2, SAE J429 GR 8 bolt when it is subjected to a temperature rise of 1508F (e.g., from 708F to 2208F) ? Define stress rel ...

A steel frame is fabricated with the cross section shown

A steel frame is fabricated with the cross section shown. The centered hole allows cables to be run up to equipment above. The frame supports a load P at a distance d from the centroid of the vertical beam. Bending of th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro