Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem1) Materials with no systematic arrangement of atoms is known as:

a) Single crystal
b) Polycrystalline
c) Amorphous
d) None of the above

problem2) Arrhenius plot of (1/T) versus lnD, gives straight line where slope of the line gives

a) Flux
b) Concentration gradient
c) Activation energy
d) None of these

problem3) Fick’s first law of diffusion mustbe used in cases where

a) Steady state diffusion occurs
b) There is change in flux with distance
c) There is a change in concentration profile with distance
d) All of the above

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93908

Have any Question? 


Related Questions in Mechanical Engineering

The mass of a he atom is less than that of an ar atom does

The mass of a He atom is less than that of an Ar atom. Does that mean that because of its larger mass, Argon exerts a higher pressure on the container walls than He at the same molar density, volume, and temperature? Exp ...

The illustration below shows a vane with a turning angle

The illustration below shows a vane with a turning angle θ which moves with a steady speed v c . The vane receives a jet that leaves a fixed nozzle with speed θ. (a) Assume that the vane is mounted on rails as shown in t ...

Water in an open cylindrical tank 15 ft in diameter

Water in an open cylindrical tank 15 ft in diameter discharges into the atmosphere through a nozzle 2 in. in diameter. Neglecting friction and the unsteadiness of the flow, find the time required for the water in the tan ...

Suppose that the performance of a bjt transistor is

Suppose that the performance of a BJT transistor is entirely limited by emitter injection efficiency, which limits the d.c. beta, and base spreading resistance, which limits the bandwidth. Show that the gain-bandwidth pr ...

A rosette composed of three strain gages measures strain at

A rosette composed of three strain gages measures strain at a point on the surface of a flat sheet of annealed stainless steel loaded in plane stress. The strains measured (numbers correspond to strain gages in the figur ...

Bull why do individual bolts relax a bit when first

• Why do individual bolts relax a bit when first tightened? Name several factors that can increase the relaxation ? Which will tend to loose more preload after initial tightening, a short bolt or a long bolt? • What are ...

The dc beta rises with collector current due to the sns

The d.c. beta rises with collector current due to the SNS effect and drops due to high injection level in the best. Combine these two effects and obtain the condition at which the beta peaks. Use the simplest formulas de ...

Project -this project is individual work write a computer

Project - This project is individual work. Write a computer program using Matlab to read the engineering constants E 1 , E 2 , v 12 , and G 12 then computes and prints the Reduced Compliances Matrix [S], the Reduced Stif ...

1 determine the capillary rise for a water-air-glass

1. Determine the capillary rise for a water-air-glass interface at 40°C in a clean glass tube having a radius of 1 mm. 2. Determine the difference in pressure between the inside and outside of a soap film bubble at 20 °C ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro