Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe the working principle of anemometer with the neat sketch. prepare differences between the accuracy and precision. Determine the limits of tolerance and allowances for a 25mm shaft and hole pair H8d2. Describe the term error and sensitivity of the measuring device with respect to the micrometer. Draw and describe the construction and working of anyone mechanical comparator clearly describeing the magnification method adopted on it. Also state its advantages and disadvantages. describe the angle gauge blocks? State their use in angle measurement.

2)  describe briefly the computer aided inspection in detail. describe the principle of operation of a rolling gear tester with a neat sketch. Specify the errors in the spur gear which may be detected by the rolling gear tester. Specify the Kelvin-Plank statement of second law of thermodynamics. Describe an Isolated system. describe what is meant by the cyclic heat engine?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913793

Have any Question? 


Related Questions in Mechanical Engineering

1 a beaker has the shape of a circular cone of diameter 7

1. A beaker has the shape of a circular cone of diameter 7 in and height 9 in. When empty, it weighs 14 oz; full of liquid, it weighs 70 oz. Find the density of the liquid in both SI and U.S. customary units. 2. Some exp ...

Each wood railroad tie supports part of the weight of a

Each wood railroad tie supports part of the weight of a train (plus the relatively small weight of a section of rail). This is modeled with two point loads representing the force of the rail on the tie. The reaction from ...

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

How do bolt stiffness and joint stiffness affect the angle

How do bolt stiffness and joint stiffness affect the angle of turn versus preload relationship? A rubber washer has been used instead of a metal one, by mistake. How will preload be affected if the same predetermined tor ...

1 identify the terms that may arise from the ground

1. Identify the terms that may arise from the ground configurations of the atoms of elements of Period 2 and suggest the order of their energies. 2. Find the first-order corrections to the energies of the hydrogen atom t ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

A bar consists of two portions bc and c d of the same

A bar consists of two portions BC and C D of the same material and of the same length L, but of different cross sections. Determine the strain energy of the bar when it is subjected to an axial load P, expressing the res ...

The propeller of a wind generator is supported by a hollow

The propeller of a wind generator is supported by a hollow circular shaft with 0.4 m outer radius and 0.3 m inner radius. The shear modulus of the material is G = 80 GPa. (a) If the propeller exerts an 840 kN · m torque ...

1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

The jet pump injects water at v1nbsp 40 ms through a 76 cm

The jet pump injects water at V 1  = 40 m/s through a 7.6 cm pipe and entrains a secondary flow of water V 2  = 3 m/s in the annular region around the small pipe. The two flows become fully mixed downstream, where V 3  i ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen