Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe some of the corners, wave guide, bands and twists?

2) describe the meaning of the term scattering matrix?

3) Describe the term Directivity of Directional coupler.

4) describe what is Faraday rotation isolator?

5) describe some of the hull cut off conditions?

6) describe the difference between the TWT and Klystron amplifier?

7) Specify the Transferred electron effect.

8) describe the application of the IMPATT.

9) Specify the methods to determine the impedance.

10) describe some of the voltage standing wave ratio?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M912970

Have any Question? 


Related Questions in Electrical & Electronics

1 outline the steps involved in the magnetoquasistatic

1. Outline the steps involved in the magnetoquasistatic field analysis of a parallel plate structure and the determination of its input behavior. Compare the input behavior with the magnetostatic case. 2. Outline the ste ...

1 what is the voltage reflection coefficient at the

1. What is the voltage reflection coefficient at the junction between two transmission lines? How are the current reflection coefficient and the voltage and current transmission coefficients related to the voltage reflec ...

Consider a deformation of a rectangular bar whose deformed

Consider a deformation of a rectangular bar whose deformed geometry is given as x 1 = αX 1 , x 2 = βX 2 , x 3 = βX 3 When the material is incompressible and St. Venant-Kirchhoff material properties are given as E = 600 M ...

1 what is a uniform plane wave2 why is the study of uniform

1. What is a uniform plane wave? 2. Why is the study of uniform plane waves important? 3. How is the surface current density vector defined? Distinguish it from the volume current density vector. 4. How do you find the c ...

A transmission line of length 2 m having a nonmagnetic

A transmission line of length 2 m having a nonmagnetic perfect dielectric is short-circuited at the far end. A variable-frequency generator is connected at its input and the current drawn is monitored. It is found that t ...

The rate at which metallic ions are electroplated from a

The rate at which metallic ions are electroplated from a dilute electrolytic solution onto a rotating disk electrode is usually governed by the mass diffusion rate of ions to the disk. This process is believed to be cont ...

1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

An ltic system impulse response is given by ht ut-ut - 1a

An LTIC system impulse response is given by h(t) = u(t)-u(t - 1). a. Determine the transfer function H(s). Using H(s), determine and plot the magnitude response |H(jω)|. Which type of filter most accurately describes the ...

A current distribution is given bywhere j0 is a constant

A current distribution is given by where J 0 is a constant. Using Ampere's circuital law in differential form and symmetry considerations, find the magnetic field everywhere.

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro