+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

1) Specify few commercial modelling software and its main applications.

2) What is meant by the concurrent engineering?

3) describe what is computational efficiency?

4) describe the translation of a coordinate.

5) describe what is Data structure?

6) Discuss the necessity of the data storage.

7) describe what is parametric design?

8) What do you understand by the geometric entity?

9) Design the types of 1D, 2D & 3D elements.

10) Finite element method is an approximation method to determine the solution-comment.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M913424

Have any Question?

## Related Questions in Mechanical Engineering

### Some experimental data for shearing stress tau and shear

Some experimental data for shearing stress τ and shear strain rate γ obtained for a particular non-Newtonian fluid at 80?F are shown below. Please plot these data and fit a second-order polynomial to the data using graph ...

### You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

### A dam discharge into a channel of constant width as shown

A dam discharge into a channel of constant width as shown. It is observed that a region of still water backs up behind the jet to a height H. The velocity and height of the flow in the channel are given as v and h, respe ...

### 1 if the density of sea water is approximated by the

1. If the density of sea water is approximated by the equation of stat is the compressibility, determine the pressure and density at a point 32,000 ft below the surface of the sea. Assume β = 300,00 psi. 2. The change in ...

### For the state of stress given in problem 517 determinea the

For the state of stress given in Problem 5.17, determine a. the maximum shear stress b. the normal stresses on the plane of maximum shear stress c. the normal and shear stresses after the element has been rotated through ...

### The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

### 1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

### A 10 hp y-connected 60 hz 380 v three-phase induction

A 10 hp, Y-connected, 60 Hz, 380 V, three-phase induction generator is used to drive a small micropower plant. The generator's load is 500 W for a 4 A line current at 1740 rpm. The rotor resistance is 4.56 Ω at 75°C. The ...

### 1 the practical depth limit for a suited diver is about 185

1. The practical depth limit for a suited diver is about 185 m. What is the gage pressure in sea water at that depth? The specific gravity of sea water is 1.025. 2. Matter is attracted to the center of Earth with a force ...

### A critical bolted joint in a nuclear power plant requires a

A critical bolted joint in a nuclear power plant requires a specific bolt preload. The access prevents a direct, accurate measurement of the actual bolt preload. It is planned to use a UNF 7/16-20 bolt with a root diamet ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro