Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe the several propagations of the wave guide?

2) Specify the various benefits of the wave guide?

3) describe the dominant mode in the wave guide? Develop the field for the TE10mode.

4) describe the dominant mode in the wave guide?

5) prepare the differences between TE and TM mode in the rectangular wave guide.

6) describe what is wave guide? describe its operation with the help of diagram.

7) Describe the term cut-off frequency of wave guide, group velocity, phase velocity and guided wave length.

8) describe how the wave is propagated within the rectangular wave guide?

9) Describe how wave guide differs from the two-wire transmission line?

10) describe the working principle of PIN diode along with its construction.

11) describe the working principle of the Gunn diode.

12) describe the construction details of the reflex klystron along with the neat and labelled diagram.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911976

Have any Question? 


Related Questions in Electrical & Electronics

Determine the maximum film velocity in problemproblem

Determine the maximum film velocity in Problem. Problem Aviscous film drains uniformly down the side of a vertical rod of radius R. At some distance down the rod, the film approaches a terminal or fully developed flow su ...

Problem 1 - a consider an isolated generating station with

Problem 1 - a. Consider an isolated generating station with a local load and with: Governor time constant and gain T G = 0, K G = 1, Turbine time constant and gain T T = 1, K T = 1 System time constant T P = 20 Total dam ...

1 a 0635-cm hydraulic line suddenly ruptures 8 m from a

1. A 0.635-cm hydraulic line suddenly ruptures 8 m from a reservoir with a gage pressure of 207 kPa. Compare the laminar and inviscid flow rates from the ruptured line in cubic meters per second. 2. A common type of visc ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

1 multnomah falls in oregon has sheer drop of 165 m

1. Multnomah Falls in Oregon has sheer drop of 165 m. Estimate the change in water temperature caused by this drop. 2. An ‘‘air cushion'' vehicle is designed to traverse terrain while floating on a cushion of air. Air, s ...

1 state the relationship between polarization current

1. State the relationship between polarization current density and electric field intensity. How is it taken into account in Maxwell's equations? 2. What is the revised definition of D? 3. State the relationship between ...

1 briefly discuss the determination of the fresnel

1. Briefly discuss the determination of the Fresnel reflection and transmission coefficientsv for an obliquely incident wave on a dielectric interface. 2. What is total internal reflection? Discuss the nature of the refl ...

1 find the velocity with which the group of two frequencies

1. Find the velocity with which the group of two frequencies 2400 MHz and 2500 MHz travels in a parallel-plate waveguide of dimension a = 2.5 cm and having a perfect dielectric of 2. For a narrow-band amplitude modulated ...

1 for the coaxial cable of example 69 employing air

1. For the coaxial cable of Example 6.9 employing air dielectric, find the ratio of the outer to the inner radii for which the characteristic impedance of the cable is 75 Ω. 2. Using the general solutions for the complex ...

A continuous-time signal x t deltat 12 is sampled at

A continuous-time signal x (t) = Δ((t = 1)/2) is sampled at three rates: 10, 2, and 1 Hz. Sketch the resulting sampled signals. Because x (t) is timelimited, its bandwidth is infinite. However, most of its energy is conc ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro