Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe the Central Limit theorem.

2) prepare differences between the Discrete and Continuous random variables.

3) describe the Weiner-Kinchine relation.

4) describe the term Ergodicity.

5) describe the term Redundancy.

6) What is meant by the mutual information?

7) Create the structure of parity check matrix H for (n, k) block code.

8) prepare down the Craft’s inequality.

9) describe the matched filter?

10)  prepare down the Friss Formula.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M912921

Have any Question? 


Related Questions in Electrical & Electronics

Let xt be a signal whose fourier transform xomega is

Let x(t) be a signal whose Fourier transform X(ω) is nonzero only over 3 ≤ |ω| ≤ 9. Further, only frequencies 5 ≤ |ω| ≤ 7 contain useful information (the other frequencies can be considered to contain noise or different ...

Question 1 a road 300 m long is required to be illuminated

Question 1. A road 300 m long is required to be illuminated by providing 40W fluorescent lamps. The width of the road is 4m. Design a street lighting scheme for obtaining minimum level of illumination of 0.6 lux assuming ...

Determine if the filters with the following transfer

Determine if the filters with the following transfer functions are physically realizable. If they are not realizable, explain if and how they can be approximately realized. Be as specific as possible. (c) H(ω)=2πδ(ω)

A signal is bandlimited to 12 khz the band between 9 and 12

A signal is bandlimited to 12 kHz. The band between 9 and 12 kHz has been corrupted by excessive noise to the point that the information within this band is nonrecoverable. Determine the minimum sampling rate for this si ...

A a signal x t 5 sinc2 5pit cos 20pit is sampled at a

a. A signal x (t) = 5 sinc 2 (5πt) + cos 20πt is sampled at a rate of 10 Hz. Find the spectrum of the sampled signal. Can x (t) be reconstructed by lowpass filtering the sampled signal? b. Repeat part (a) for a sampling ...

The state equations of a certain system are given asfind

The state equations of a certain system are given as Find the state equations of the system with w as the state vector. Determine the characteristic roots (eigenvalues) of the matrix A in the original and the transformed ...

A certain communication channel has a bandwidth of 10 khz a

A certain communication channel has a bandwidth of 10 kHz. A pulse of 0.5 ms duration is transmitted over this channel. a. Determine the width (duration) of the received pulse. b. Find the maximum rate at which these pul ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

1 why is it that the distances r1 and r2 in the phase

1. Why is it that the distances r 1 and r 2 in the phase factors in equations (8.47a) and (8.47b) cannot be set equal to r, but the same quantities in the amplitude factors can be set equal to r? 2. What is an array fact ...

Assignmentpart 1 electricians tools1 which of the following

Assignment Part 1: Electricians' Tools 1. Which of the following types of symbols would be used on an electrical drawing for a large machine? A. Schematic symbols B. Blueprint symbols C. Pictorial symbols D. Wiring symbo ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen