+1-415-315-9853

info@mywordsolution.com

## Engineering

 Civil Engineering Chemical Engineering Electrical & Electronics Mechanical Engineering Computer Engineering Engineering Mathematics MATLAB Other Engineering Digital Electronics Biochemical & Biotechnology

1) describe the retrieval and generative types of CAPP with appropriate diagrams.

2) With the help of suitable flow diagram, describe how a computerized shop floor control system works.

3) describe the different strategies which can be employed for process control in detail.

4) Describe about the non-contact inspection methods of optical category with appropriate diagrams in detail.

5) Describe the functions of computer in the computer Integrated Manufacturing system (CIMS).

6) describe the basic components of a DNC system with a simple block diagram. Also, describe its functions.

7) Describe about configuration and control features of an Automated storage and Retrieval system.

8) prepare brief notes on:

(a) Automated Guided Vehicles and

(b) Database Management Systems.

Mechanical Engineering, Engineering

• Category:- Mechanical Engineering
• Reference No.:- M913343

Have any Question?

## Related Questions in Mechanical Engineering

### Assigned work clearly indicate all assumptions and

Assigned Work (Clearly indicate all assumptions and references) 1. A 500 m 2 light colored swimming pool is located at (a) normal suburban site, (b) well-sheltered site, where the measured wind speed at 10 m height is 3 ...

### Linear motion actuator with feedback controlanalyses and

Linear Motion Actuator with Feedback Control Analyses and Simulations Provide complete mathematical modeling of the system and its components (free body diagrams and differential equations are required). Provide a comple ...

### A cantilever beam ab supports a uniform load of intensity q

A cantilever beam AB supports a uniform load of intensity q acting over part of the span and a concentrated load P acting at the free end, as shown. Determine the deflection and slope at end B of the beam. The beam has l ...

### A simply supported beam 5 m long is loaded with a 20 n

A simply supported beam 5 m long is loaded with a 20 N downward force at a point 4 m from the left support. The second moment of area of the cross-section of the beam is 4I 1 for segment AB and I 1 for the remainder of t ...

### 1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

### We isolate n moles of an ideal gas with heat capacity cpm

We isolate n moles of an ideal gas with heat capacity CPm and then heat the gas and allow it to expand from a state P1 ,V1 ,T1 to a inal state P2 ,V2 ,T2 . Find a general formula for the S of this process by treating the ...

### How would you identify the best nut factor for your

How would you identify the best nut factor for your application? How much torque would be required to tighten an ASTM A193 Gr. B16 bolt with a 31/4-8 thread to 60% of yield? Why does a wrench create a side load on the bo ...

### Experiment title heat engine experimentacademic in charge

Experiment title: Heat Engine Experiment Academic in charge of experiment: Experiment duration: The standard scheduled time for this experiment is 90 minutes for 3 groups (A, B, C) of 6 students. Each group undertakes ex ...

### Write an engineering paper talking about nano-structure gas

Write an engineering paper talking about Nano-structure gas sensors. I have an outline that I need you to follow and Also I provided all the sources you need to write the paper. High performance nano-structured Zinc Oxid ...

### In order to penetrate a workpiece a tungsten carbide drill

In order to penetrate a workpiece, a tungsten carbide drill bit is subject to a torque of 3.8 Nm and an axial force of 5 kN. Tungsten carbide is very strong (compressive strength 1400 MPa, tensile strength 340 MPa) but a ...

• 13,132 Experts

## Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

### Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

### Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

### Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

### Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

### Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen