Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1. Describe the process of LBM and PAM with a neat and suitable sketches.

2.(i) describe the process parameters of EBM and their influence on machining quality.

(ii) Describe the process capabilities of EBM and PAM in detail.

3.(i) Describe the principle of LBM with neat and suitable sketch.

(ii) prepare down the advantage and limitation of LBM process.

4.(i) Describe the principle of PAM with suitable sketch

(ii) prepare down the advantage and limitation of PAM process.

5.(i) What is the application of EBM.

(ii) What do you mean by EBM? Design its set up to indicate its major parts and describe the principle of operation.

6.(i) Describe the principles and elements of EBM, also how work table is protected from getting damaged by electron beam.

(ii) Describe how process variables influence MRR, HAZ and pattern generation in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911704

Have any Question? 


Related Questions in Mechanical Engineering

This atomic force microscope probe is a silicon beam and

This atomic force microscope probe is a silicon beam and tip. The beam is 40 µm wide, 4 µm thick, and 130 µm long. The tip is set back 15 µm from the end of the cantilever. The deflection of the tip is 1 µm for every 42 ...

1 use simple classical particle kinetics to show that the

1. Use simple classical particle kinetics to show that the transvers electric field in the MOST is not a fundamental cause of mobility and drift velocity variation with the electric fields. 2. Find maximum oscillation fr ...

The viscosity of heavy liquids such as oils is frequently

The viscosity of heavy liquids, such as oils, is frequently measured with a device that consists of a rotating cylinder inside a large cylinder. The annular region between these cylinders is filled with liquid and the to ...

A cable with a length h a cross-sectional area a and

A cable with a length H, a cross-sectional area A, and modulus E is attached to the end of a cantilever beam with length L, second moment of area I, and modulus E (same modulus as the cable). The beam is loaded with a fo ...

1 write down the equations for the reverse active mode by

1. Write down the equations for the reverse active mode by inspection without doing any algebra. 2. Are there any currents flowing in the cutoff mode? What is their magnitude if there are? 3. Obtain the saturation voltag ...

Confirm that in hydrogenic atoms the spin-orbit coupling

Confirm that in hydrogenic atoms, the spin-orbit coupling constant depends on n and l as in eqn 7.24 2.Calculate the spin-orbit coupling constant for a 2p-electron in a Slater-type atomic orbital, and evaluate it for the ...

Complete the report with taking care the followingschapter

Complete the report with taking care the followings: Chapter 1 Air Pollution Historical Remarks What Is An Air Pollutant? Pollutant Emissions Primary Gaseous Pollutants Primary Particulate Matter Radioactive Pollutants S ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

A room has design conditions of78 f db and 50 rh and a rscl

A room has design conditions of78 F DB and 50% RH and a RSCL = 18,000 BTUlhr and RLCL = 8000 BTUlhr. An air conditioning unit supplies 900 CFM of air to the room at 58 F DB and 56 F WB. Will the unit maintain the room de ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen