Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

a) List out the different types of stokers and describe any two in detail.
b) Describe various modern ash handling equipments with neat sketches.

problem 2:

a) Describe the different control methods to decrease thermal emissions.
b) describe the working of cyclone separator with appropriate sketch.

problem 3:

a) Describe the different lubrication systems of diesel engine power plant.
b) Describe the functions of necessary components of diesel power plant.

problem 4:

a) Describe in detail the factors that affect the selection of gas turbines.
b) Describe the working of modern Francis turbine. How do you govern it?

problem 5:
a) describe the necessary elements of hydroelectric power plant with appropriate sketch.
b) Describe hydro power generation equipments with neat sketches.

problem 6:

a) What are the desirable properties of a good moderator? Illustrate the advantages and limitations of breeder reactor.
b) Describe sodium cooled reactor with neat sketch.

problem 7: Describe in detail pulverized fuel firing equipments with neat diagrams.

problem 8: Enlist the different cooling methods of diesel engine and elucidate the working of thermostat controlled cooling system with proper diagram.

problem 9: Describe the working of combined hydroelectric station and thermal station.  Illustrate its advantages and limitations.

problem 10: Describe the functions of necessary components of a nuclear power plant. In addition describe nuclear fission and chain reaction.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93147

Have any Question? 


Related Questions in Mechanical Engineering

As an approximate rule a particular vibrational mode in a

As an approximate rule, a particular vibrational mode in a molecule will contribute to the equipartition principle energy at temperatures where 3 2 kBT Ú ve for that mode. In the following table are listed all the vibrat ...

The average heat evolved by the oxidation of foodstuffs in

The average heat evolved by the oxidation of foodstuffs in an average adult per hour per kilogram of body weight is 7.20 kJ kg-1 hr -1 . Assume the weight of an average adult is 62.0 kg. Suppose the total heat evolved by ...

1 determine the capillary rise for a water-air-glass

1. Determine the capillary rise for a water-air-glass interface at 40°C in a clean glass tube having a radius of 1 mm. 2. Determine the difference in pressure between the inside and outside of a soap film bubble at 20 °C ...

The vibrational partition function for an unknown diatomic

The vibrational partition function for an unknown diatomic molecule at 300 K is 2.33. Find the maximum value of the vibrational constant ve in cm-1 such that at least 5% of the molecules in a 300 K sample will be found i ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

Sea water rho 1025 kgm3 flows through a pump at 021 m3s

Sea water, ρ = 1025 kg/m 3 , flows through a pump at 0:21 m 3 /s. The pump inlet is 0.25 m in diameter. At the inlet the pressure is -0.15 m of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The ...

1 a glass bulb of volume 0198 l contains 0457 g of gas at

1. A glass bulb of volume 0.198 L contains 0.457 g of gas at 759.0 Torr and 134.0°C. What is the molar mass of the gas? 2. A 455 cm 3 vessel contains a mixture of Ar and Xe. If the mass of the gas mixture is 2.245 g at 2 ...

Question 1derive an expression for the velocity vector of

Question 1: Derive an expression for the velocity vector of the collar D, N V D. The upper arm (B) rotates about a horizontal axis ( nˆ x ) at a rate q · 1 The lower arm (C) Rotates about the longitudinal axis of B (bˆ z ...

1 for the pipe-flow-reducing section d1nbsp 8 cm d2nbsp 5

1. For the pipe-flow-reducing section D 1  = 8 cm, D 2  = 5 cm, and p 2  = 1 atm. If v 1  = 5 m/s and the manometer reading is h =58 cm, estimate the total force resisted by the flange bolts. 2. An open tank car as shown ...

In practice how could you measure that much stretch in a

In practice, how could you measure that much stretch in a bolt of this size? The bolt of problem is put in service and its temperature rises to 2508F. How much change in length of the bolt would you expect this increase ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro