Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) List out any two cooling systems that are used in IC engines.

2) Specify the desirable qualities of SI engines fuel to inhibit detonation.

3) describe the methods for determining the B.P of IC engines.

4) describe what is charge stratification?

5) Show on same p-v diagram-the compression process with perfect cooling and imperfect inter cooling, for two stage compressor.

6) describe the meaning of free air delivered.

7) Specify the condition of the refrigerant at the end of compression in vapour c0mpression system.

8) Describe why is throttle valve used in place of expansion cylinder for vapour compression refrigeration machine?

9) describe the dew point temperature of humid air. Also specify how it is related to partial Pressure of water vapour in the moist air?

10) describe the term Re-heat factor.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913547

Have any Question? 


Related Questions in Mechanical Engineering

Define nut dilation why can it be a problemcompute the

Define nut dilation. Why can it be a problem? Compute the approximate thermal expansion of a 1=2-13 2, SAE J429 GR 8 bolt when it is subjected to a temperature rise of 1508F (e.g., from 708F to 2208F) ? Define stress rel ...

Problem -a piston at one end of a gas filled circular tube

Problem - A piston at one end of a gas filled circular tube of area S oscillates with real-valued velocity: U p (t) = U 1 cos(ω 1 t) + U 2 sin(ω 2 t) Note that two oscillation frequencies are present. The other end of th ...

A 15 m tall utility pole is located at a 40deg bend in a

A 15 m tall utility pole is located at a 40° bend in a set of power lines. The tension in each line is 15 kN, and due to sag of the lines, the tension forces act along directions 10° below horizontal. A guy wire has been ...

Name the principal modes of failure of both tensile and

Name the principal modes of failure of both tensile and shear joints? Describe or list the criteria a bolted joint designer must consider when selecting bolt size and material for a new joint? Will short, fat bolts gener ...

1 explain the read write erase operations of the fmosc

1. Explain the read, write, erase operations of the FMOSC memory cell shown in Fig. 674.4(b). Fig. 674.4 2. Is an initial charge up operation of the FMOSC memory cells necessary immediately after the d.c. power turned on ...

1 a beaker has the shape of a circular cone of diameter 7

1. A beaker has the shape of a circular cone of diameter 7 in and height 9 in. When empty, it weighs 14 oz; full of liquid, it weighs 70 oz. Find the density of the liquid in both SI and U.S. customary units. 2. Some exp ...

A series of calibration tests is conducted on a pressure

A series of calibration tests is conducted on a pressure gage. At a known pressure of 1000 psia it is found that 30 percent of the readings are within 1 psia of the true value. At a known pressure of 500 psia, 40 percent ...

Many devices have been developed to measure the viscosity

Many devices have been developed to measure the viscosity of fluids. One such device, known as a rotational viscometer, involves a pair of concentric cylinders with radii r i and r o , and total length L. The inner cylin ...

What must the bolts in a shear joint do to prevent its

What must the bolts in a shear joint do to prevent its failure? Describe some of the factors that make it difficult to create an exact and predicted amount of clamping force during assembly? How does an external load on ...

A potential flow source having an intensity of 10m2s placed

A potential flow source having an intensity of 10m2/s, placed in the point of Cartesian coordinates (1;0), and a sink having identical intensity, placed in the point (-1;0), are combined with a uniform flow at 25 m/s, in ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro