Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1)a) With appropriate graph describe the relationship between action potential and Muscle contraction.

(b) Describe in detail how pulsatile blood volume changes can be measured by using Photoelectric type resistive transducer.

2) Describe with neat and suitable sketch anatomy and conducting system of heart. Also describe cardio vascular circulating system with block diagram.

3) Describe with neat sketch anatomy and physiology of central nervous and peripheral nervous system.

4) Sketch diagrams demonstrating the process of respiration and circulation.

(ii) Sketch the diagram and equivalent circuit of differential capacitance pressure transducer and briefly describe its operation.

5)(i) describe the generation and features of action potential and Resting Potential in detail.

(ii) prepare down the requirements of good physiological transducer and describe the operation of any two types of physiological transducers with relevant sketches?

6) Design the structure of a living cell of our body and describe in its constituents detail.

7)(i) Describe the working of Piezoelectric transducer as arterial pressure sensor.

(ii) Describe how Piezo electric transducer produces Ultrasonic waves.

8) prepare brief notes on:

(i) Strain guage type chest transducer

(ii) Transducer as respiration sensor

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911420

Have any Question? 


Related Questions in Electrical & Electronics

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

The trigonometric fourier series of a certain periodic

The trigonometric Fourier series of a certain periodic signal is given by a. Sketch the exponential Fourier spectra. b. By inspection of the spectra in part (a), sketch the trigonometric Fourier spectra for x(t). Find th ...

1 if the plate shown is inclined at an angle as shown what

1. If the plate shown is inclined at an angle as shown, what are the forces F x  and F y  necessary to maintain its position? The flow is frictionless. 2. A steady, incompressible, frictionless, two-dimensional jet of fl ...

Clculate the surface integral of the vector function f

Calculate the surface integral of the vector function, F = xe 1  + ye 2 , over the portion of the surface of the unit sphere, S : x 2  + y 2  + z 2  = 1, above the xy-plane, i.e., z > 0.

Power mosfet breakdown voltage 800v must conduct 10a when

power mosfet breakdown voltage 800v must conduct 10A when on with a maximum on state voltage 4v.If the current density in the mosfet must be limited to 200A/cm,estimate the conduxting area

A discuss asymptotic and bibo stabilities for the systems

a. Discuss asymptotic and BIBO stabilities for the systems described by the following transfer functions assuming that the systems are controllable and observable: b. Repeat part (a) for systems described by the followin ...

1 what is the significance of a nonzero net right-lateral

1. What is the significance of a nonzero net right-lateral differential of and normal to the z-direction at a point in space? 2. If a pair of E and B at a point satisfies Faraday's law in differential form, does it neces ...

1 discuss the consequence of the frequency dependence of

1. Discuss the consequence of the frequency dependence of the phase velocity of a wave in a material medium. 2. What is loss tangent? Discuss its significance. 3. What is the intrinsic impedance of a material medium? Wha ...

1 discuss how the cutoff condition arises in a waveguide2

1. Discuss how the cutoff condition arises in a waveguide. 2. Explain the relationship between the cutoff wavelength and the spacing between the plates of a parallel-plate waveguide based on the phenomenon at cutoff.

A force f is applied at the tip of the uniform bar element

A force F is applied at the tip of the uniform bar element shown in the figure. The initial length and the cross-sectional area of the bar are, respectively, A 0  and L 0 . The elastic modulus of the material is E. Calcu ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro