Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe what do you understand by the term source and sink? For the same compression ratio state which of two cycles the Otto and Diesel is more efficient? describe what is an air standard cycle? Describe what is quality of steam? Specify what is meant by the dryness fraction of the steam? State few exs for the solid, liquid and gaseous fuels.describe the calorific value of fuel?

2) describe the special purpose of lathes? Specify the function of back gear? describe the different types of chucks that are available? Specify the several kinds of drilling machine tools. describe the counter boring operation. Describe the differences between the vertical turret lathe and the vertical boring machine? Compare and contrast the plain and universal milling. Describe the standard size of the planer?

3) What are the different kinds of Precision grinders? describe the several broaching methods that are available? Sketch layout of lathe and describe the various parts of Lathe. describe the different kinds of Lathe. Describe in brief. State different kinds of drilling machines operation and describe each with the neat sketch. describe the different work holding devices in a drilling machine?  Describe Horizontal boring machine with a neat diagram in detail.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913794

Have any Question? 


Related Questions in Mechanical Engineering

Name at least three reasons why some bolts fail

Name at least three reasons why some bolts fail mechanically? What is the most common cause of bolted joint misbehavior or failure? Name at least two problems that can be caused by overtightening the bolts? What do we me ...

A small three-phase ig has the following nameplate data 110

A small three-phase IG has the following nameplate data: 110 V, 1.140 rpm, 60 Hz, Y connection, and 1250 W. The blocked rotor test at 60 Hz yielded the following: I = 69.4 A, P = 4200 W. The turn ratio between stator and ...

In order to maneuver a large ship while docking pumps are

In order to maneuver a large ship while docking, pumps are used to issue a jet of water perpendicular to the bow of the ship as shown in the figure. The pump inlet is located far enough away from the outlet that the inle ...

Name the two types of bolted joints and tell why theyre

Name the two types of bolted joints and tell why they're called that? What is the main mission of the bolts in any joint? What factor largely determines the behavior and life of a tensile joint? Why are bolted joints oft ...

A fan draws air from the atmosphere through a 030-mdiameter

A fan draws air from the atmosphere through a 0.30-mdiameter round duct that has a smoothly rounded entrance. A differential manometer connected to an opening in the wall of the duct shows a vacuum pressure of 2.5 cm of ...

An open tank l ft long as shown below travels to the right

An open tank L ft long as shown below travels to the right at a velocity v c  fps. A jet of area A j  exhausts fluid of density r at a velocity v j  fps relative to the car. The tank car, at the same time, collects fluid ...

An isotopically enhanced sample has ndi moles of deuterated

An isotopically enhanced sample has nDI moles of deuterated hydrogen iodide and nHI moles of common HI at 398 K. Comparison of the infrared intensities of the v = 1 S 2 transition inds a ratio of 0.100 for DI molecules ( ...

1 how large as a fraction of the supported weight w must

1. How large (as a fraction of the supported weight W) must the weight w of the forearm and hand be to change the analysis done under the assumption of weightlessness? 2. What sort of simple measurement or experiment cou ...

Heat transfer problem -a thermocouple is to be utilized to

Heat Transfer Problem - A thermocouple is to be utilized to measure the temperature of exhaust gases from an automobile engine and the effect of the cylindrical radiation shield installed as shown in the image, is to be ...

Experiment title heat engine experimentacademic in charge

Experiment title: Heat Engine Experiment Academic in charge of experiment: Experiment duration: The standard scheduled time for this experiment is 90 minutes for 3 groups (A, B, C) of 6 students. Each group undertakes ex ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro