Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe what is sampling process?

2) Describe the meaning of zero order hold?

3) describe what is meant by the Z-transform? prepare down the application.

4) describe the different properties of the Z-transform?

5) Describe the non-linearities in the control system?

6) describe some of the properties of the non-linear system?

7) describe the phase plane analysis?

8) Describe what is meant by the iso-cline in phase plane analysis?

9) describe what is state, and state space of a system?

10) Specify the condition of controllability.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913161

Have any Question? 


Related Questions in Electrical & Electronics

The performance of a journal bearing around a rotating

The performance of a journal bearing around a rotating shaft is a function of the following variables: Q, the rate of flow lubricating oil to the bearing in volume per unit time; D, the bearing diameter; N, the shaft spe ...

Show that if a periodic signal xt is an even function of t

Show that if a periodic signal x(t) is an even function of t, then all the sine terms in its trigonometric Fourier series vanish, and if x(t) is an odd function of t, all the cosine terms vanish. In either case, show tha ...

Power mosfet breakdown voltage 800v must conduct 10a when

power mosfet breakdown voltage 800v must conduct 10A when on with a maximum on state voltage 4v.If the current density in the mosfet must be limited to 200A/cm,estimate the conduxting area

1 explain the self-consistency condition for waveguiding in

1. Explain the self-consistency condition for waveguiding in a dielectric slab waveguide. 2. Discuss the dependence of the number of propagating modes in a dielectric slab waveguide on the ratio of the thickness d of the ...

A rectangular plastic specimen of size 100 x 100 x 10

A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions of the cavity are 101 X 101 X 9 mm 3 . The plastic is compressed by a rigid punch until it is completely ...

Question 1 design a suitable double -layer lap winding for

Question 1) Design a suitable double -layer lap winding for a 6-pole dc armature with 18 slots and two coil sides per slot. Give values of front-pitch, brack-pitch and commutator pitch. Draw the developed diagram and sho ...

1 define wavelength how is it related to the phase

1. Define wavelength. How is it related to the phase constant? 2. What is the relationship between frequency, wavelength, and phase velocity? What is the wavelength in free space for a frequency of 15 MHz? 3. What is the ...

A line assumed to be infinitely long and of unknown

A line assumed to be infinitely long and of unknown characteristic impedance when connected to a line of characteristic impedance 50 Ω produces a standing wave ratio of value 2 in the 50-Ω line. The same line when connec ...

1 discuss the physical phenomena associated with each of

1. Discuss the physical phenomena associated with each of the elements in the transmissionline equivalent circuit. 2. What is a transverse electromagnetic wave? 3. What is a field map? Describe the procedure for drawing ...

A communication link at a frequency of 30 mhz uses a

A communication link at a frequency of 30 MHz uses a half-wave dipole for the transmitting antenna and a small loop (directivity equal to 1.5) for the receiving antenna, involving a distance of 100 km. The antennas are o ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen