Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) a) describe the different kind of machining operation which can be carried on the lathe.

b) List out the benefit of using the taper turning attachment.

2) a) Draw the tooling lay out for generation of the Hexagonal Bolt.

b) Specify the benefit of using the collet chuck.

3) a) Draw and describe the radial drilling machine.

b) describe the benefit of the Hydralic shaper over crank shaper.

4) a) Draw the jig borer and describe it’s working.

b) Compare and Contrast between the boring and reaming.

5) a) describe the three kinds of the milling cutters with the help of neat sketch.

b) prepare a brief note on any two milling operation.

6) Describe the following topic:

a) Gear Hobber

b) Lapping

c) Honing

7) Describe the principal of Electron Beam machining with the help of neat sketch and also specify the limitations of the EBM.

8) Discuss the working principle of the Electrical Discharge machining. with a neat sketch and also state its advantages and disadvantages of EBM.

9) a) Describe the point to Point Positioning System and Straight-cut positioning system.

b) State the significant elements of the N.C systems.

10 ) Describe the point to point positioning control system and the straight-cut positioning system.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913413

Have any Question? 


Related Questions in Mechanical Engineering

For the state of stress given in problem 517 determinea the

For the state of stress given in Problem 5.17, determine a. the maximum shear stress b. the normal stresses on the plane of maximum shear stress c. the normal and shear stresses after the element has been rotated through ...

Calculate the fraction of n2 molecules in a sample at 298 k

Calculate the fraction of N2 molecules in a sample at 298 K that have speeds less than 10.0ms -1 by integrating the Maxwell-Boltzmann distribution over the appropriate range of speeds (just writing the correct integral i ...

Task to identify research and present in both written and

Task: To identify, research, and present (in both written and oral formats) a topic in engineering that is currently the focus of ongoing (within the past 5 years) research, investigation, and/or development.The topic mu ...

A sample of he ions is prepared at a temperature of 298 k

A sample of He + ions is prepared at a temperature of 298 K and a density of 2.0 # 10 10 cm -3 . Because these are ions, magnetic ields may be used to trap those ions with kinetic energy less than some threshold value et ...

1 sketch the deformation of a fluid element for the

1. Sketch the deformation of a fluid element for the following cases: 2. For a two-dimensional, incompressible flow with velocity v x  = v x (y), sketch a three-dimensional fluid element and illustrate the magnitude, dir ...

Invent a structure that can completely eliminate the narrow

Invent a structure that can completely eliminate the narrow gate effects. This is known as the fully recessed stepped oxide (FROSOX) whose sidewall oxide is thicker than the gate oxide and they are connected by a step or ...

Derive a counterpart for the case of plane strain in the

Derive a counterpart for the case of plane strain in the xz-plane of the compatibility equation shown in Problem 4.15 for plane stress. How does this plane strain result differs from the compatibility equation for plane ...

A beam with a rectangular cross section has dimensions as

A beam with a rectangular cross section has dimensions, as defined in Fig. 8.13, of b = 40and t = 10 mm. The beam is made of 7475-T7351 aluminum and is subjected to a bendingmoment of M = 900 N·m. (a) If a through-thickn ...

1 at 60degc the surface tension of water is 00662 nm and

1. At 60°C the surface tension of water is 0.0662 N/m and that of mercury is 0.47 N/m. Determine the capillary height changes in these two fluids when they are in contact with air in a glass tube of diameter 0.55 mm. Con ...

A dilute suspension contains ten spheres per liter a sample

A dilute suspension contains ten spheres per liter. A sample (one tenth of that solution) is removed. What is the probability that there is (a) at least one sphere, (b) at most one sphere in the sample. You may assume th ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen