Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Design a layout for a thermal plant and describe the functions of each components of that plant.

2) What do you mean by chain reaction in nuclear power plant? Also describe the process of nuclear fusion?

3)(a) prepare down the advantages and Disadvantages of hydro-power plant.

(b) Describe the functions of the following 1.Reservoir, 2.Dam, 3.Spill ways, 4. Intake, 5. Fore bay, 6. Penstock, 7.Surge tank.

4) What do you mean by pumped storage plants? describe the principle of operation of such a plant with neat sketch. Also describe the role of this plant in a large inter-connected power system?

5) describe with neat sketch construction and principle of operation of an electro static precipitator. prepare down its advantage over mechanical ash separators.

6) prepare brief notes on 1. Condensers, 2. Economizers. 3. Air pre heaters 4. Super heater. 5. feed water system. 6. Cooling tower.

7)(i) prepare down electrical systems and sub stems used in aircraft and its requirements.

(ii) describe the construction of prime move for aircraft generator in detail.

8) Describe the working of a gas turbine power plant with a suitable schematic diagram.

9) Design block diagram of a diesel power station and describe its operation. What is the requirement for distributed generating system?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M911452

Have any Question? 


Related Questions in Mechanical Engineering

The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

If in the system for problem the total drag on the object

If, in the system for Problem, the total drag on the object is measured to be 800 N/m of length normal to the direction of flow, and frictional forces at the walls are neglected, find the pressure difference between inle ...

A watertight bulkhead 22 ft high forms a temporary dam for

A watertight bulkhead 22 ft high forms a temporary dam for some construction work. The top 12 ft behind the bulkhead consists of sea water with a density of 2 slugs/ft 3  , but the bottom 10 ft begin a mixture of mud and ...

You are asked to design a cylindrical scuba tank with a

You are asked to design a cylindrical scuba tank with a radius R = 16 cm to a pressure of p = 12.0 MPa at a factor of safety of 2.0 with respect to the yield stress. The relevant tabulated yield values for the steel of w ...

Health insurance market place healthcaregov a project

Health Insurance Market Place (healthcare.gov): A Project Management Perspective The information: Use information from: 1) "From the Start, Signs of Trouble at Health Portal(Which is in the attached PDF file)" and 2) "Ho ...

Two closed rigid water containers with initial temperatures

Two closed, rigid water containers with initial temperatures T A and T B are brought into thermal contact. At equilibrium, the two containers are at the same temperature. Prove that this process has positive ?S and find ...

What do we mean by the term torque reaction a right angle

What do we mean by the term torque reaction? A right angle nut runner is used to produce 500 ft-lb of torque on a bolt having a 7/8 -9 UNC thread. The tool is 18 in. long. How much reaction force, created by the reaction ...

We have the task to design an industrial lift table

We have the task to design an industrial lift table according to the following principle sketch where L = 1200 mm. We should be able to control the table height between 320 mm (min height) to 1040 mm (max height), with t ...

The viscosity eta of water at various temperatures t is

The viscosity η of water at various temperatures T is given in the following table Compute the cubic splines that pass through the three given points. Evaluate the viscosity at 25°C. The measured value has been reported ...

1 the practical depth limit for a suited diver is about 185

1. The practical depth limit for a suited diver is about 185 m. What is the gage pressure in sea water at that depth? The specific gravity of sea water is 1.025. 2. Matter is attracted to the center of Earth with a force ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen