Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Q1) describe the following term:

a) Accuracy

b) Precision

c) Stability

d) Lag

Q2) describe the following term:

a) Speed of response

b) Dead zone

c) Drift

d) Fidelity.

Q3) describe the following term:

a) Average value

b) RMS value

c) Sensitivity

d) Instrument

Q4) describe the following term:

a) Resolution

b) Calibration

c) Absolute instrument

d) Secondary instrument.

Q5) describe the following term:

a) Dynamic error

b) Repeatability

c) Reproducibility

d) Error

e) Measurement.

Q6) describe the following term:

a) Resolution

b) Accuracy with respect to digital display.

Q7) Define the term errors. describe how it is classified and specify any two types of the errors.

Q8) Describe the meaning of shielding and grounding with the help of diagram. Why is it required?

Q9) describe the classification of instrument.

Q10) What do you understand by the term calibration. describe the significance of the calibration of instruments.

Q11) What is meant by Standard? describe what primary and secondary standards are?

Q12) describe the term “voltmeter sensitivity” of the analog multimeter.

Q13) Provide some of the advantages and disadvantages of the PMMC instrument.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911929

Have any Question? 


Related Questions in Electrical & Electronics

Figure 3013 shows a router using priority queuing at the

Figure 30.13 shows a router using priority queuing at the input port. The arrival and required service times (transmission time is negligible) for 10 packets are shown below; ti means that the packet has arrived i ms aft ...

Suppose that a discrete-time system is described by the

Suppose that a discrete-time system is described by the frequency response Find the frequency response of an equivalent system whose frequency response has five terms of ejv in the numerator and six terms of ejv in the d ...

Assignmentpart 1 conductors1 a type tw cable containing two

Assignment: Part 1: Conductors 1. A type TW cable containing two No. 12 copper conductors has a maximum overcurrent protection of A. 15 A. B. 25 A. C. 30 A. D. 20 A. 2. Which one of the following types of wire can be use ...

1 state maxwells equations for static fields ina integral

1. State Maxwell's equations for static fields in (a) integral form, and (b) differential form. 2. Discuss the classification of static fields with reference to subsets of Maxwell's equations. 3. Outline the steps involv ...

A line assumed to be infinitely long and of unknown

A line assumed to be infinitely long and of unknown characteristic impedance is connected to a line of characteristic impedance on which standing wave measurements are made. It is found that the standing wave ratio is 3 ...

1 what is a divergence meter how does it help visualize the

1. What is a divergence meter? How does it help visualize the behavior of the divergence of a vector field? 2. Provide two examples of physical phenomena in which the divergence of a vector field is nonzero. 3. State the ...

1 briefly outline the reasoning used for the removal of the

1. Briefly outline the reasoning used for the removal of the inconsistency with Maxwell's equations of the intuitively derived fields due to the Hertzian dipole. 2. Discuss the characteristics of the complete electromagn ...

Determine the spacing relative amplitudes and phase angles

Determine the spacing, relative amplitudes, and phase angles of current densities for an array of two infinite plane parallel current sheets required to obtain a radiation characteristic such that the field radiated to o ...

Assignmentbefore you start please read the following

Assignment Before you start please read the following instructions carefully. 1. This assignment forms part of the formal assessment for this module. If you fail to reach the required standard for the assignment then you ...

Given the message accbcaab in which the probabilities of

Given the message "ACCBCAAB*", in which the probabilities of symbols are P(A) = 0.4, P(B) = 0.3, P(C) = 0.2, and P(*) = 0.1, a. find the compressed data using arithmetic coding with a precision of 10 binary digits. b. fi ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro