Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe the term gap contraction factor.

2) Describe what is meant by the specific electric loading?

3) describe the benefits of selecting the higher number of poles.

4) describe the different factors limiting the design of the main dimension in dc machines?

5) describe the benefits of the stepped core in transformers.

6) List out the several kinds of the winding that are used in the transformer.

7)  Specify the several factors which affect the choice of number of the stator slots.

8) describe the benefits of selecting the smaller length of air gap within the induction motor design?

9) Describe the term short circuit ratio.

10) describe the several kinds of the poles that are used in the salient pole machines?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913067

Have any Question? 


Related Questions in Electrical & Electronics

1 discuss with the aid of an example the discharging of an

1. Discuss with the aid of an example the discharging of an initially charged line into a resistor. 2. Discuss the bounce-diagram technique of transient analysis of a line with uniform initial voltage and current distrib ...

1 a 15 v aa battery that costs 1 is rated at 18 ah what is

1. A 1.5 V AA battery that costs $1 is rated at 1.8 Ah. What is its cost per kWh? 2. Suppose a 12-V battery bank rated at 200 Ah under standard conditions needs to deliver 600 Wh over a 12-h period each day. If they oper ...

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m2 in size, has its own 90% effi- cient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the ...

Assignmentpart 1 conductors1 a type tw cable containing two

Assignment: Part 1: Conductors 1. A type TW cable containing two No. 12 copper conductors has a maximum overcurrent protection of A. 15 A. B. 25 A. C. 30 A. D. 20 A. 2. Which one of the following types of wire can be use ...

1 define the parts of flow specification in intserv2

1. Define the parts of flow specification in IntServ. 2. Distinguish between guaranteed services and controlled-load services in IntServ. 3. IntServ is normally called a destination-based service. Explain the reason. 4. ...

Using the navier-stokes equations in appendix e solve

Using the Navier-Stokes equations in Appendix E, solve Problem. Problem The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary case. The case and the drum are ...

For a uniform plane wave propagating in free space the

For a uniform plane wave propagating in free space, the apparent phase velocities along the x- and y-directions are found to be respectively. Find the direction of propagation of the wave.

A number equal to the sum of its coordinates is assigned to

A number equal to the sum of its coordinates is assigned to each point in a rectangular room having three of its contiguous edges as the coordinate axes. Draw a sketch of the constant-magnitude surfaces for the number fi ...

1 define standing wave ratio swr what are the standing wave

1. Define standing wave ratio (SWR). What are the standing wave ratios for (a) an infinitely long line, (b) a short-circuited line, (c) an open-circuited line, and (d) a line terminated by its characteristic impedance? 2 ...

1 for a point charge q situated at the point 1 2 0 find the

1. For a point charge Q situated at the point (1, 2, 0), find the potential difference between the point A(3, 4, 1) and the point B(5, 5, 0). 2. For the arrangement of a linear electric dipole consisting of point charges ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen