Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe about the Wire frame, Surface and Solid modelling.

2) describe the following terms:

a) CAD geometry

b) CAD hardware

c) Engineering analysis

3) a) describe the advantages of CAPP.

b) Describe Machinability Data System.

4) describe the methods of CAPP? Describe any one method in detail.

5) a) Describe the advantages of Group Technology.

b) Assume that four machines 1,2,3,and 4 have been identified as belonging in a GT machine Cell. An Analysis of 50 Parts processed on these machines has been summarized in the From – To Chart of Table shown below. Determine a logical machine arrangement using To/From ratio method and find the back flow ratio.

To
From              1        2           3         4
1                    0        5           0        25
2                    30      0           15      15
3                    10      40          0         0
4                    10       0           20       0

6) Describe the detail procedure of classifying the parts by production flow analysis.

7) Describe the following given terms:

a)Traffic control

b) System management

8) Describe the following given terms:

a) Interfacing handling

b) Robot.

9) Describe the following given terms:

a) Reverse engineering

b) Risks in concurrent engineering

c) Lead time.

10) Describe what is Agile Manufacturing? Discuss how the production system keeps pace with the market forces.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M913673

Have any Question? 


Related Questions in Mechanical Engineering

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

A stationary jet engine is shown air with a density of

A stationary jet engine is shown. Air with a density of 0.0805 lb m /ft 3  enters as shown. The inlet and outlet cross-sectional areas are both 10.8 ft 2 . The mass of fuel consumed is 2% of the mass of air entering the ...

Sea water rho 1025 kgm3 flows through a pump at 021 m3s

Sea water, ρ = 1025 kg/m 3 , flows through a pump at 0:21 m 3 /s. The pump inlet is 0.25 m in diameter. At the inlet the pressure is -0.15 m of mercury. The pump outlet, 0.152 m in diameter, is 1.8 m above the inlet. The ...

Question 1 consider the motion of an axially symmetric body

Question 1. Consider the motion of an axially symmetric body in the absence of torques. Find the analytical solution for the Euler angles as a function of time. Question 2. Show that the ellipsoid of inertia of a cube of ...

1 discuss the four best-known practical methods of

1. Discuss the four best-known practical methods of generating residual magnetism. 2. Discuss the advantages of a matrix partition to represent the transient state of an aggregation of SEIGs. 3. Using the state variable ...

Heat transfer problem -a thermocouple is to be utilized to

Heat Transfer Problem - A thermocouple is to be utilized to measure the temperature of exhaust gases from an automobile engine and the effect of the cylindrical radiation shield installed as shown in the image, is to be ...

Electrical current is passed through a resistor immersed in

Electrical current is passed through a resistor immersed in a liquid in an adiabatic container. The temperature of the liquid is varied by 1°C. The system consists solely of the liquid. Does heat or work flow across the ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

If you could go back in time and be part of any engineering

If you could go back in time and be part of any engineering achievement in the past, what would you choose? Your choice must involve something that was accomplished before 1970, although it might still be in use today. Y ...

1 concrete rocks and bone are strong in compression and are

1. Concrete, rocks, and bone are strong in compression and are usually designed for compressive loading. To test their strength in compression, what sort of test specimen would be useful? 2. Suppose that a downward force ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen