Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe what is meant by the term Computer Integrated Manufacturing?

2) describe the hardware included in the CIM.

3) describe some of the advantages of the Computer Aided Design.

4) describe what is meant by the term scaling?

5) describe various types of the productions.

6) describe what is meant by the term work-in progress?

7) List some of the design attributes that is considered in GT.

8) describe some of the advantages of Machine Cell?

9) describe some of the benefits of FMS.

10) What is meant by the term Lean manufacturing?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912326

Have any Question? 


Related Questions in Mechanical Engineering

1 water is flowing through a large circular conduit with a

1. Water is flowing through a large circular conduit with a velocity profile given by the equation v = 9(1- r 2 /16) fps. What is the average water velocity in the 1.5-ft pipe? 2. Water enters a 4-in. square channel as s ...

In problem above find the depth at which the net force on

In Problem above, find the depth at which the net force on the tank is zero. Problem :- On a certain day the barometric pressure at sea level is 30.1 in. Hg, and the temperature is 708F. The pressure gage in an airplane ...

Problem -an aluminum extrusion was created in the shape at

Problem - An aluminum extrusion was created in the shape at the right as shown with the origin at the lower left corner. Show all work in finding the centroid (4). Find moments of inertia with respect to the x and y axes ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

A transformer winding was designed to be fed by an ac

A transformer winding was designed to be fed by an ac voltage of 110 V and to produce an effective current of 10.5 A. By mistake, the transformer was fed from this same voltage but rectified in a full wave converter. Con ...

1 draw the moment diagram for the elbow-biceps-forearm-hand

1. Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment. 2. How do the magnitudes of the biceps force B and joint reaction J change if the total ...

For the allen wrench of problem 715 what is the deflection

For the allen wrench of Problem 7.15, what is the deflection of the tip of the wrench when the maximum load of 60 N is applied, just before the bolt loosens? Problem 7.15: The maximum force applied to the tip of the alle ...

What primary factors determine the number of load cycles

What primary factors determine the number of load cycles required to break a bolt subject to fatigue loading? Describe the appearance of the break surface of a bolt which has failed in fatigue ? Where on a bolt are you m ...

A steel bar with the cross section shown and effective

A steel bar with the cross section shown and effective length L = 2.5 m is subjected to a compressive load P = 200 kN with a eccentricity e = 0.00625 m. Find (a) the beam's maximum deflection, and (b) the maximum normal ...

During the test of a centrifugal pump a bourdon pressure

During the test of a centrifugal pump, a Bourdon pressure gage just outside the casing of the 12-in.-diameter suction pipe reads 6 psig (i.e., vacuum). On the 10-in. -diameter discharge pipe another gage reads 40 psig. T ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro