Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) describe what is meant by the term Computer Integrated Manufacturing?

2) describe the hardware included in the CIM.

3) describe some of the advantages of the Computer Aided Design.

4) describe what is meant by the term scaling?

5) describe various types of the productions.

6) describe what is meant by the term work-in progress?

7) describe few design features that are considered in the GT.

8) describe some of the advantages of the Machine Cell?

9) describe some of the FMS benefits.

10) describe the meaning of the Lean manufacturing?

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912297

Have any Question? 


Related Questions in Mechanical Engineering

The probability of a linear molecule being in a particular

The probability of a linear molecule being in a particular rotational level J depends on the temperature, and for J 7 0 there is a temperature Tmax at which the probability for that level reaches a maximum. Derive an exp ...

Two closed rigid water containers with initial temperatures

Two closed, rigid water containers with initial temperatures T A and T B are brought into thermal contact. At equilibrium, the two containers are at the same temperature. Prove that this process has positive ?S and find ...

Project -this project is individual work write a computer

Project - This project is individual work. Write a computer program using Matlab to read the engineering constants E 1 , E 2 , v 12 , and G 12 then computes and prints the Reduced Compliances Matrix [S], the Reduced Stif ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

A gas sample is known to be a mixture of ethane and butane

A gas sample is known to be a mixture of ethane and butane. A bulb having a 230.0 cm 3 capacity is filled with the gas to a pressure of 97.5 X 10 3 Pa at 23.1°C. If the mass of the gas in the bulb is 0.3554 g, what is th ...

1 the following data define the sea-level concentration of

1) The following data define the sea-level concentration of dissolved oxygen for fresh water as a function of temperature: T 0 8 16 24 32 40 01F 14.64 11.85 9.87 8.41 7.30 6.43 Use MATLAB to fit the data with (a) piecess ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

Derive a formula for the minimum energy in the

Derive a formula for the minimum energy in the two-dimensional Using model, if the interaction energy between each spin and each of its eight nearest neighbors is -D. Assume that the model consists of a rectangular array ...

If you were using a full length centerline gage rod to

If you were using a full length, centerline, gage rod to measure DL, how much change would you expect to see at 2508F?  What DL from ‘‘before tightening'' would you expect to see at 2508F if you were using ultrasonics to ...

1 a square gate 4 m by 4 m is located on the 45deg face of

1. A square gate, 4 m by 4 m, is located on the 45° face of a dam. The top edge of the gate is 8 m below the water surface. Determine the resultant force of the water on the gate, and the point through which it acts. 2. ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro