Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

Answer the following problems in detail.

problem 1) describe Potential Energy approach used in FEM in detail.

problem 2) In what circumstances are the triangular elements useful in FEA?

problem 3) prepare down the shape functions of a four-node quadrilateral element.

problem 4) Why is FEA considered as the approximate solution method? Describe in detail.

problem 6) describe the use of quadrilateral element in detail.

problem 7) prepare down the difference between the cartesian coordinate and natural coordinate system.

problem 8) What do you mean by isoparametric elements?

problem 9) prepare down the Gauss Quadrature rule used in FEA.

problem 10) Mention Saint Venant's Principle. Describe the Rayleigh-Ritz method used in FEA.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M98967

Have any Question? 


Related Questions in Mechanical Engineering

An air conditioner is a refrigerator with the inside of the

An air conditioner is a refrigerator with the inside of the house acting as the cold reservoir and the outside atmosphere acting as the hot reservoir. Assume that an air conditioner consumes 1.70 X 10 3 W of electrical p ...

The fugacity and fugacity coefficient are determined as a

The fugacity and fugacity coefficient are determined as a function of pressure and temperature for a model gas. These variables can be varied using sliders. The student is asked to determine the Boyle temperature and als ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

1 what requirements control the derivation of load-stress

1. What requirements control the derivation of load-stress relations? 2. Describe the method of mechanics of materials. 3. How arc stress-strain-temperature relations for a material established? 4. Explain the difference ...

1 using matlabsimulinkreg write a computer program to

1. Using MATLAB/Simulink®, write a computer program to represent the SEIG in its transient state. 2. Explain why an IG cannot self-excite under the following conditions: (1) no residual magnetism, (2) after too much indu ...

Consider the torsion of a thin-walled tube determine an

Consider the torsion of a thin-walled tube. Determine an approximate expression for the torque if the shear stress must be less than a given working stress τw. Express this result in terms of the tube's mean radius R and ...

Water flows steadily through the piping junction entering

Water flows steadily through the piping junction, entering section 1 at 0.0013 m 3  /s. The average velocity at section 2 is 2.1 m/s. A portion of the flow is diverted through the showerhead, which contains 100 holes of ...

For the state of stress given in problem 517 determinea the

For the state of stress given in Problem 5.17, determine a. the maximum shear stress b. the normal stresses on the plane of maximum shear stress c. the normal and shear stresses after the element has been rotated through ...

Calculate the size h of the two welds required to attach a

calculate the size h of the two welds required to attach a plate to a frame as shown in figure. if the plate supports an inclined force P=50kn. use a factor safety of 3 and yield shear stress of 350 mpa for the weld mate ...

Name the principal modes of failure of both tensile and

Name the principal modes of failure of both tensile and shear joints? Describe or list the criteria a bolted joint designer must consider when selecting bolt size and material for a new joint? Will short, fat bolts gener ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro