Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) In a peripheral-mapped I/O, can an input port and the output port have the same port address? Describe in detail.

problem 2) prepare down the control signals that are essential in the memory-mapped I/O?

problem 3) Name the four categories of 8085 instructions which manipulate data.

problem 4) describe opcode and operand, and state the opcode and the operand in the instruction MOV H, L.

problem 5) prepare down logical steps to add following two Hex numbers. Both the numbers must be saved for future use. Store the sum in an accumulator. Numbers: A2H and 18H.

problem 6) State the contents of registers and flag status as the following instructions are executed.

i) MVI A, 00H

ii) MVI B, F8H

iii) MOV C, A

iv) MOV D, B

v) HLT

problem 7) prepare down instructions to load hexadecimal number 65H in register C and 92H in accumulator A. Show the number 65H at PORT0 and 92H at PORT1.

problem 8) Draw and describe the block diagram of a microprocessor 8085.

problem 9) Why the lower order address bus is multiplexed with data bus? How they will be de-multiplexed?

problem 10) Distinguish between maskable and non-maskable interrupts.

problem 11) prepare down 8085 assembly language program using minimum number of instructions to add 16 bit no. in BC, DE & HL. Save the 16 bit result in DE pair.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99212

Have any Question? 


Related Questions in Electrical & Electronics

The name plate of a squirrel-cage four-pole induction motor

The name plate of a squirrel-cage four-pole induction motor has the following information: 25 hp, 220 volts, three-phase, 60 Hz, 830 rev/min, 64A line current. If the motor draws 20,800 watts when operating at full load, ...

1- if the largest secdiv you can set is 10s what is the

1- If the largest sec/div you can set is 10s, what is the lowest frequency AC signal you can measure with the digital oscilloscope (to see at least one full period)? 2- If the smallest sec/div you can set is 10μs, what i ...

A using schematics plot the power delivered to the resistor

a. Using schematics, plot the power delivered to the resistor R of given figure for R having values from 1 to 50Ω. b. From the plot, determine the value of R resulting in maximum power to R and the maximum power to R. c. ...

An fm modulator is followed by an ideal band pass filter

An FM modulator is followed by an ideal band pass filter having a center frequency of 500 Hz and a bandwidth of 70 Hz. The gain of the filter is 1 in the pass band. The unmodulated carrier is given by a. Determine the pe ...

Ariatnam najafi and morones journal of professional issues

Ariatnam, Najafi, and Morones (Journal of Professional Issues in Engineering Education And Practice, 2002) describe an overview of academies on horizontal directional drilling conducted to train engineers and inspectors ...

Determine the generator matrix for the coder illustrated in

Determine the generator matrix for the coder illustrated in Figure 11.15. Use the generator matrix to generate the complete set of code words and use the results to check the code words shown in Figure 11.15. Show that t ...

Show the connections required to establish 4 komega between

Show the connections required to establish 4 kΩ between the wiper arm and one outside terminal of a 10-kΩ potentiometer while having only zero ohms between the other outside terminal and the wiper arm.

A materials engineer wants to study the effects of two

A materials engineer wants to study the effects of two different processes for sintering copper (a process by which copper powder coalesces into a solid but porous copper) on two different types of copper powders. From e ...

For the bridge network of given figurea write the nodal

For the bridge network of given figure: a. Write the nodal equations using the format approach. b. Determine the current across R 5 . c. Is the bridge balanced? d. Is given Equation satisfied?

A full-wave scr converter circuit is used to regulate the

A full-wave SCR converter circuit is used to regulate the power across a 10Ω resistance. The voltage source is 120V (rms). At a triggering angle of 72°, compute the power across the load and the rms currents of the load.

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

A cola-dispensing machine is set to dispense 9 ounces of

A cola-dispensing machine is set to dispense 9 ounces of cola per cup, with a standard deviation of 1.0 ounce. The manuf

What is marketingbullwhat is marketing think back to your

What is Marketing? • "What is marketing"? Think back to your impressions before you started this class versus how you

Question -your client david smith runs a small it

QUESTION - Your client, David Smith runs a small IT consulting business specialising in computer software and techno

Inspection of a random sample of 22 aircraft showed that 15

Inspection of a random sample of 22 aircraft showed that 15 needed repairs to fix a wiring problem that might compromise

Effective hrmquestionhow can an effective hrm system help

Effective HRM Question How can an effective HRM system help facilitate the achievement of an organization's strate