Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) describe Procedure and Macro in detail and compare them.

2) describe the purpose of segment registers in 8086.

3) What do you mean by pipelining?

4) describe the function of instruction queue in 8086.

5) Determine the maximum memory size which can be addressed by 8086?

6) What is the function of the signal in 8086?

7) What are the predefined interrupts in 8086?

8) What are the different flag available in status register of 8086?

9) prepare down the different addressing modes present in 8086?

10) describe how single stepping can be done in 8086.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910944

Have any Question? 


Related Questions in Electrical & Electronics

If the shock-wave velocity in problem is approximated by

If the shock-wave velocity in Problem is approximated by the speed of sound, determine the pressure change causing a velocity change of 10 fps in (a) air at standard conditions; (b) water. Problem:- The shock wave illust ...

1 in jpeg explain why we need to round the result of

1. In JPEG, explain why we need to round the result of division in the quantization step. 2. Explain why the combination of quantization/dequantization steps in JPEG is a lossy process even though we divide each element ...

A discuss asymptotic and bibo stabilities for the systems

a. Discuss asymptotic and BIBO stabilities for the systems described by the following transfer functions assuming that the systems are controllable and observable: b. Repeat part (a) for systems described by the followin ...

The size d of droplets produced by a liquid spray nozzle is

The size d of droplets produced by a liquid spray nozzle is thought to depend upon the nozzle diameter D, jet velocity V, and the properties of the liquid ρ, μ, and σ. Rewrite the relation in dimensionless form. Take D, ...

Consider a bar element as shown in the figure the

Consider a bar element as shown in the figure. The cross-sectional areas are A 1  and A 2  at nodes 1 and 2, respectively, and vary linearly. In addition, the gravitational acceleration is applied along the axial directi ...

1 a program for encoding and decoding lzw compression2 a

1. A program for encoding and decoding LZW compression. 2. A program for encoding and decoding arithmetic compression. 3. A program that reads a two-dimensional matrix of size N × N and writes the values using zigzag ord ...

1 if the ram and auto rack in the previous problem together

1. If the ram and auto rack in the previous problem together have a mass of 680 kg, estimate the maximum sinking speed of the ram and rack when gravity and viscous friction are the only forces acting. Assume 2.44 m of th ...

Determine the spacing relative amplitudes and phase angles

Determine the spacing, relative amplitudes, and phase angles of current densities for an array of two infinite plane parallel current sheets required to obtain a radiation characteristic such that the field radiated to o ...

A bounded-amplitude signal xt has bilateral laplace

A bounded-amplitude signal x(t) has bilateral Laplace transform X(s) given by a. Determine the corresponding region of convergence. b. Determine the time-domain signal x(t).

Given the message accbcaab in which the probabilities of

Given the message "ACCBCAAB*", in which the probabilities of symbols are P(A) = 0.4, P(B) = 0.3, P(C) = 0.2, and P(*) = 0.1, a. find the compressed data using arithmetic coding with a precision of 10 binary digits. b. fi ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen