Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1) Describe unit impulse response in detail.

2) prepare down the difference between energy and power signals.

3) prepare down the condition for even and odd signals.

4) Determine the laplace transform of e-2t.

5) What do you mean by DTFT pair?

6) describe final value theorem for Z-Transform.

7) Determine whether the system is shift invariant y(n)=x(n)-x(n-2).

8) Describe how Z transform is related to Fourier transform?

9) describe static and dynamic system

10) What do you mean by transfer function?

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M912666

Have any Question? 


Related Questions in Electrical & Electronics

Boiler efficiency and heat losses heat balence sheet boiler

Boiler efficiency and heat losses, heat Balence sheet, boiler draught, high pressure boiler

Question 1consider the following wireless receiver chain

Question 1: Consider the following wireless receiver chain consisting of a low noise amplifier (LNA), bandpass filter and mixer, as depicted below. The LNA receives its input signal from an antenna. a) If the input noise ...

1 explain the self-consistency condition for waveguiding in

1. Explain the self-consistency condition for waveguiding in a dielectric slab waveguide. 2. Discuss the dependence of the number of propagating modes in a dielectric slab waveguide on the ratio of the thickness d of the ...

Another method used in a ciphertext attack see previous

Another method used in a ciphertext attack (see previous problem) is called the statistical approach, in which the intruder intercepts a long ciphertext and tries to analyze the statistics of the characters in the cipher ...

1 what is meant by the dominant mode why are waveguides

1. What is meant by the dominant mode? Why are waveguides designed so that they propagate only the dominant mode? 2. Why is the dimension b of a rectangular waveguide generally chosen to be less than or equal to one-half ...

1 why is a circle with its center at the center of the

1. Why is a circle with its center at the center of the Smith Chart known as a constant SWR circle? Where on the circle is the corresponding SWR value marked? 2. Using the Smith Chart, how do you find the normalized line ...

Referring to the figure assume the flow to be frictionless

Referring to the figure, assume the flow to be frictionless in the siphon. Find the rate of discharge in cubic feet per second, and the pressure head at B if the pipe has a uniform diameter of 1 in. How long will it take ...

1 obtain the equations for a one-dimensional steady viscous

1. Obtain the equations for a one-dimensional steady, viscous, compressible flow in the x direction from the Navier- Stokes equations. (These equations, together with an equation of state and the energy equation, may be ...

For each of the following baseband signals i mt cos 1000t

For each of the following baseband signals (i) m(t) = cos 1000t, (ii) m(t) = 2cos 1000t + cos 2000t, and (iii) m(t) = cos 1000t cos 3000t: a. Sketch the spectrum of m(t). b. Sketch the spectrum of the DSB-SC signal m(t) ...

1 what would be the voltage and current standing wave

1. What would be the voltage and current standing wave patterns for an open-circuited line? 2. Discuss the variation with frequency of the input reactance of a short-circuited line and its application in the determinatio ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen