Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

1) Describe the major components of the CIM.

2) describe the 3 basic network topologies.

3) prepare a brief notes on the following topics:

a) Rotation

b) Translation

c) Editing in CAD.

4) describe about common facilities that are available in the solid modelling package.

5) describe the types of Automation with appropriate exs.

6) describe what is capacity planning? Describe the adjustments required for Capacity planning.

7) Describe the production flow analysis with the appropriate ex.

8) describe several types of the machine cells and their layouts with proper sketches.

9) describe the Material handling and storage systems that are used in FMS.

10) Describe the rolls that is played by computers in the FMS.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912303

Have any Question? 


Related Questions in Mechanical Engineering

1 the hypodermic needle shown below contains a liquid serum

1. The hypodermic needle shown below contains a liquid serum (ρ = 1 g/cm 3 ). If the serum is to be injected steadily at 6 cm 3  /s, how fast should the plunger be advanced (a) if leakage in the plunger clearance is negl ...

1 in more than one paragraph but less than a page discuss

1. In more than one paragraph but less than a page, discuss some of the failure modes experienced in the collapse of the World Trade Center and how they might have been prevented. 2. A truss ABC supports a load W at join ...

The velocity profile in the annular control volume of

The velocity profile in the annular control volume of Example is approximately linear, varying from a velocity of zero at the outer boundary to a value of ωd/2 at the inner boundary. Develop an expression for the fluid v ...

A liquid column of height h is confined in a vertical tube

A liquid column of height h is confined in a vertical tube of cross-sectional area A by a stopper. At t = 0, the stopper is suddenly removed, exposing the bottom of the liquid to atmospheric pressure. Using a control-vol ...

Wat is the resilience of the bolts and joint this time

What is the resilience of the bolts and joint this time? What is the stiffness ratio of this eccentric joint? By how much does the tensile load of 7.40 kips increase the tension in the bolts and reduce the clamping force ...

The space between two very long parallel plates separated

The space between two very long parallel plates separated by a distance h is filled with a fluid with viscosity where μ0 is a constant and n is a constant exponent. The top plate slides to the right with a constant speed ...

An incompressible fluid flows past a flat plate as in the

An incompressible fluid flows past a flat plate, as in the figure below, with a uniform inlet profile and a polynomial exit profile Compute the volume flow Q across the top surface of the control volume. The plate has wi ...

1 water in a container is originally at 100 kpa the water

1. Water in a container is originally at 100 kPa. The water is subjected to a pressure of 120 MPa. Determine the percentage decrease in its volume. 2. Determine the height to which water at 68°C will rise in a clean capi ...

Leaning polea pole of negligible mass leans against a wall

Leaning pole A pole of negligible mass leans against a wall, at angle ? with the horizontal. Gravity is directed down (a) Find the constraint relating the vertical acceleration of one end to the horizontal acceleration o ...

Experiment title heat engine experimentacademic in charge

Experiment title: Heat Engine Experiment Academic in charge of experiment: Experiment duration: The standard scheduled time for this experiment is 90 minutes for 3 groups (A, B, C) of 6 students. Each group undertakes ex ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen