Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Q1. Draw the system architecture of DMA by using the ISA bus protocol and describe its memory prepare bus cycle.

Q2. Draw the two-level bus architecture of microprocessor-based embedded system and describe it.

Q3. Memory allocation and management are the most significant functions of the kernel. describe why? How does memory allocation distinct in RTOS and OS? What do you mean by memory locking?

Q4. Describe the various methods of saving and optimizing the memory space.

Q5. Describe an I2C bus at the given OSI-compliant levels of detail: physical, data link, network, and transport.

Q6. Describe protocol which would permit sensor nodes in a sensor network to find out the other nodes by which they can communicate.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M911014

Have any Question? 


Related Questions in Electrical & Electronics

A discuss asymptotic and bibo stabilities for the systems

a. Discuss asymptotic and BIBO stabilities for the systems described by the following transfer functions assuming that the systems are controllable and observable: b. Repeat part (a) for systems described by the followin ...

Suppose that a continuous-time system is described by the

Suppose that a continuous-time system is described by the impulse response a. Compute the transfer function of the system. b. Find out if the system is BIBO stable. c. Plot the poles and the zeros of the system. d. Write ...

1 define the parts of flow specification in intserv2

1. Define the parts of flow specification in IntServ. 2. Distinguish between guaranteed services and controlled-load services in IntServ. 3. IntServ is normally called a destination-based service. Explain the reason. 4. ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

Assignment questiondesign automatic fan speed controller

Assignment Question Design automatic fan speed controller based on the temperature variation in room using a microcontroller. Abstract: The electronic Circuit used to control the speed of fan based on temperature variati ...

1 the rocket nozzle shown below consists of three welded

1. The rocket nozzle shown below consists of three welded sections. Determine the axial stress at junctions 1 and 2 when the rocket is operating at sea level. The mass flow rate is 770 lb m /s. 2. The pressure on the con ...

1 a program for encoding and decoding lzw compression2 a

1. A program for encoding and decoding LZW compression. 2. A program for encoding and decoding arithmetic compression. 3. A program that reads a two-dimensional matrix of size N × N and writes the values using zigzag ord ...

1 rework problem with the assumption that the momentum of

1. Rework Problem with the assumption that the momentum of the incoming air at section (1) is zero. Determine the exit velocity, v, and the magnitude of the pressure drop at section (1). 2. Air of density 1.21 kg/m 3  is ...

Assume we have a very simple message digest our unrealistic

Assume we have a very simple message digest. Our unrealistic message digest is just one number between 0 and 25. The digest is initially set to 0. The cryptographic hash function adds the current value of the digest to t ...

1 discuss how the cutoff condition arises in a waveguide2

1. Discuss how the cutoff condition arises in a waveguide. 2. Explain the relationship between the cutoff wavelength and the spacing between the plates of a parallel-plate waveguide based on the phenomenon at cutoff.

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen