Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1: Draw & describe the architectural diagram of 8051 µc.

problem 2: Discuss the following signals of 8051 µc- INT0/INT1, RD,PSEN,ALE,TO & T1,EA,TXD,RXD

problem 3: Draw & describe About I/O Ports & Ckts 8051 Μc with their alternate functions.

problem 4: describe the working of 8051 oscillator and clock & draw the timing diagram.

problem 5: Draw the Programming model of 8051 µc . How the memory is organized in 8051 µc .

problem 6: Draw the formats of following registers & describe the function of each bit -TCON, TMOD, SCON, PCON, IP, IE&PSW.

problem 7: Interface 16KB RAM & 32KB EPROM to 8051 µc.

problem 8: describe about the serial communication modes of 8051 µc.

problem 9: describe about the timer/counter modes of 8051 µc.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M93543

Have any Question? 


Related Questions in Electrical & Electronics

1 distinguish between centralized and decentralized p2p

1. Distinguish between centralized and decentralized P2P networks. 2. What are the advantages and disadvantages of a centralized P2P network? 3. What are the advantages and disadvantages of a decentralized P2P network? 4 ...

For an ltid system specified by the equationa find the

For an LTID system specified by the equation a. Find the amplitude and the phase response. b. Find the system response y[n] for the input x[n] = cos (0.5k - (π/3)).

1 in kademlia assume m 4 and active nodes are n4 n7 and

1. In Kademlia, assume m = 4 and active nodes are N4, N7, and N12. Where is the key k3 stored in this system? 2. In Chord, assume the size of the identifier space is 16. The active nodes are N3, N6, N8, and N12. Show the ...

Consider the problem of performing system identification as

Consider the problem of performing system identification as shown previously in Figure 9.49. Suppose the system to be identified is the following IIR filter. Write a MATLAB program that uses the FDSP toolbox function f l ...

1 define the parts of flow specification in intserv2

1. Define the parts of flow specification in IntServ. 2. Distinguish between guaranteed services and controlled-load services in IntServ. 3. IntServ is normally called a destination-based service. Explain the reason. 4. ...

1 briefly discuss the determination of the fresnel

1. Briefly discuss the determination of the Fresnel reflection and transmission coefficientsv for an obliquely incident wave on a dielectric interface. 2. What is total internal reflection? Discuss the nature of the refl ...

1 what would be the voltage and current standing wave

1. What would be the voltage and current standing wave patterns for an open-circuited line? 2. Discuss the variation with frequency of the input reactance of a short-circuited line and its application in the determinatio ...

1 why is it that the distances r1 and r2 in the phase

1. Why is it that the distances r 1 and r 2 in the phase factors in equations (8.47a) and (8.47b) cannot be set equal to r, but the same quantities in the amplitude factors can be set equal to r? 2. What is an array fact ...

1 show that the radiation fields given by equations 925a

1. Show that the radiation fields given by equations (9.25a) and (9.25b) do not by themselves satisfy both of Maxwell's curl equations. 2. Find the value of r at which the amplitude of the radiation field term in equatio ...

Find the zero-state response yt of the network in fig p44-1

Find the zero-state response y(t) of the network in Fig. P4.4 -1 if the input voltage x(t) = te-tu(t). Find the transfer function relating the output y(t) to the input x(t). From the transfer function, write the differen ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen