Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1: Describe the working principle of a pneumatic speed control circuit.

problem 2: Draw the neat sketch of the pneumatic filter and describe its construction and working. Also provide the graphical symbol.

problem 3: Design an electro hydraulic circuit for the given sequences A+B+A-B- where A & B stand for cylinder (+) points out extension and (-) points out retraction of cylinders. Incorporate provision for auto-manual selector and emergency stop.

problem 4: Describe in detail the considerations taken while designing the pneumatic circuits.

problem 5: Draw a pneumatic circuit diagram and describe its working for cylinder cycle timing system.

problem 6: Describe the working of fluidic amplifiers.

problem 7: Tabulate the different faults, probable causes and as well the remedial actions for the given Hydraulic and pneumatic system components:

a) Pump  
b) Compressor  
c) FRL unit  
d) Hydraulic cylinders

problem 8: Draw a neat sketch of an electro hydraulic servo valve and point out all the components and give their functions.  As well develop the transfer function for the open loop gain for this valve.

problem 9: Describe the working principle of a PLC with neat block diagram.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93698

Have any Question? 


Related Questions in Mechanical Engineering

An electronic scoreboard is to be installed in a large

An electronic scoreboard is to be installed in a large stadium. Due to the design of the roof structure, the suspending cables will have different lengths, as is shown below. a. Determine a suitable cross-sectional area ...

A liquid column of height h is confined in a vertical tube

A liquid column of height h is confined in a vertical tube of cross-sectional area A by a stopper. At t = 0, the stopper is suddenly removed, exposing the bottom of the liquid to atmospheric pressure. Using a control-vol ...

Problem 1 -there is a circular combined open and closed

Problem 1 - There is a circular combined open and closed thin-walled section as shown in the figure. (R = 100mm, t = 2mm, S y = 100N) When shear force S y is applied to Web 24, calculate: a) Calculate I xx for the x-axis ...

Q1 how did the roman way of waging war contrast with the

Q1. How did the Roman way of waging war contrast with the Greek way? JUST ANSWER THIS QUESTION WITH 150 WORDS ONLY.( NO SOURCES, SIMPLE ANSWER AND VERY SIMPLE ENGLISH SINCE IM AN INTERNATIONAL STUDENT) Q 2. What was acco ...

The tires of the 4555-lb sedan are 65 in wide figure p510

The tires of the 4555-lb sedan are 6.5 in. wide (Figure P5.10). Each tire contacts the ground over a distance of 4.25 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the ...

Calculate the power factor of an electronic system subject

Calculate the power factor of an electronic system subject to a reasonable amount of harmonics given as THD(v) = 1.0%, the displacement factor is 0.92. What would be the calculated error if harmonic components were not t ...

1 an automobile is driving into a 45-mph headwind at 40 mph

1. An automobile is driving into a 45-mph headwind at 40 mph. If the barometer reads 29 in. Hg and the temperature is 40°F, what is the pressure at a point on the auto where the wind velocity is 120 fps with respect to t ...

It has been observed that the most effective way to crush

It has been observed that the most effective way to crush an empty aluminum beverage can is to apply an eccentric compressive load. Use buckling theory to explain this phenomenon. The can wall thickness is 80 μm, and the ...

Draw the moment diagram for the elbow-biceps-forearm-hand

Draw the moment diagram for the elbow-biceps-forearm-hand system and determine the magnitude and location of the maximum moment if the total weight w of the forearm and hand are included and are assumed to act at the mid ...

Suppose that the performance of a bjt transistor is

Suppose that the performance of a BJT transistor is entirely limited by emitter injection efficiency, which limits the d.c. beta, and base spreading resistance, which limits the bandwidth. Show that the gain-bandwidth pr ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen