Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

Illustrate the following techniques of surface finish measurement.

a) Tomlinson surface meter and

b) Profilometer.

problem 2:

Discuss the interferometer measurements of angle with neat sketch.

problem 3:

With the use of neat sketch illustrate the different types of CMM based on its construction. prepare the advantages of computer aided inspection.

problem 4:

Discuss the construction and working of the Orifice meter and Rota meter.

problem 5:

With the use of neat sketches, illustrate the working of a bimetallic thermometer and Thermistor.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M912790

Have any Question? 


Related Questions in Mechanical Engineering

Problem -a piston at one end of a gas filled circular tube

Problem - A piston at one end of a gas filled circular tube of area S oscillates with real-valued velocity: U p (t) = U 1 cos(ω 1 t) + U 2 sin(ω 2 t) Note that two oscillation frequencies are present. The other end of th ...

Each wood railroad tie supports part of the weight of a

Each wood railroad tie supports part of the weight of a train (plus the relatively small weight of a section of rail). This is modeled with two point loads representing the force of the rail on the tie. The reaction from ...

A steel frame is fabricated with the cross section shown

A steel frame is fabricated with the cross section shown. The centered hole allows cables to be run up to equipment above. The frame supports a load P at a distance d from the centroid of the vertical beam. Bending of th ...

A potential flow source having an intensity of 10m2s placed

A potential flow source having an intensity of 10m2/s, placed in the point of Cartesian coordinates (1;0), and a sink having identical intensity, placed in the point (-1;0), are combined with a uniform flow at 25 m/s, in ...

A cubical piece of wood with an edge l in length floats in

A cubical piece of wood with an edge L in length floats in the water. The specific gravity of the wood is 0.90. What moment M is required to hold the cube in the position shown? The right-hand edge of the block is flush ...

1 water in a container is originally at 100 kpa the water

1. Water in a container is originally at 100 kPa. The water is subjected to a pressure of 120 MPa. Determine the percentage decrease in its volume. 2. Determine the height to which water at 68°C will rise in a clean capi ...

It is desired to design a pump-piping system to keep a

It is desired to design a pump-piping system to keep a 1-million-gallon capacity water tank filled. The plan is to use a modified (in size and speed) version of the model A centrifugal pump. Provided is the test data for ...

Assume that the level of water in the tank remains the same

Assume that the level of water in the tank remains the same and that there is no friction loss in the pipe, entrance, or nozzle. Determine (a) The volumetric discharge rate from the nozzle; (b) The pressure and velocity ...

A water jet pump has an area ajnbsp 006 ft2nbspand a jet

A water jet pump has an area A j  = 0:06 ft 2  and a jet velocity v j  = 90 fps, which entrains a secondary stream of water having a velocity v s  = 10 fps in a constant-area pipe of total area A = 0.6 ft 2 . At section ...

1 an ion with the configuration f 2 enters an environment

1. An ion with the configuration f 2 enters an environment of octahedral symmetry. What terms arise in the free ion, and with which terms do they correlate in the complex? 2. In the strong field case, the configuration d ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen