Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Design two converters – boost-buck (Cuk) and flyback meeting the following criteria:

  • Vin = 15 V … 35 V  
  • Vout = 25 V
  • Output voltage ripple 1% peak to peak
  • Switching frequency 150 kHz
  • Load 10 W … 50 W

The design should take into account non-ideal effects such as non-zero ON saturation voltage of the transistor and non-zero ON voltage drop across the diode. You should select appropriate components from the LTSpice library. Do not use ideal switches in the final design. The design does not include the controller, so you should just find out the required duty cycles for the converters. Use as small as possible values of the transfer sources which still ensure that the output voltage meets the design criteria and the converters operate safely in continuous mode. The report should include:

  • Detailed analysis and design of the converters.
  • LTSpice analysis results.
  • Conclusions.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M91254

Have any Question? 


Related Questions in Electrical & Electronics

Identify the variables associated with given problem and

Identify the variables associated with given Problem and find the dimensionless parameters. Problem The device in the schematic diagram below is a viscosity pump. It consists of a rotating drum inside of a stationary cas ...

1 are both ah and esp needed for ip security why or why

1. Are both AH and ESP needed for IP security? Why or why not? 2. What are the two protocols discussed in this chapter that provide security at the transport layer? 3. What is IKE? What is its role in IPSec? 4. What is t ...

A signal is bandlimited to 12 khz the band between 9 and 12

A signal is bandlimited to 12 kHz. The band between 9 and 12 kHz has been corrupted by excessive noise to the point that the information within this band is nonrecoverable. Determine the minimum sampling rate for this si ...

Solve problem using force equilibrium ie internal force

Solve Problem using force equilibrium; i.e., internal force caused by stress is equal to external force. Problem A force F is applied at the tip of the uniform bar element shown in the figure. The initial length and the ...

Problem 1please provide a brief and clear answer to the

Problem 1 Please provide a brief and clear answer to the following questions. (1) By saying that the electrostatic filed is conservative, we do NOT mean that (a) Its curl is identically zero. (b) It is the opposite of th ...

1 what is the magnetic flux crossing an infinitesimal

1. What is the magnetic flux crossing an infinitesimal surface oriented parallel to the magnetic flux density vector? 2. For what orientation of the infinitesimal surface relative to the magnetic flux density vector is t ...

A bug starts at a point and travels 1 m northwardm

A bug starts at a point and travels 1 m northward, m eastward, m southward, m westward, m northward, and so on, making a 90°-turn to the right and halving the distance each time. (a) What is the total distance traveled b ...

Problem 1 an amplifier is observed to have an output noise

Problem 1: An amplifier is observed to have an output noise rms-voltage of 1.0 μV. If the noise bandwidth is 25 kHz, determine the noise spectral density of the amplifier. Problem 2: A piezeoresistive sensor has a therma ...

1 distinguish between centralized and decentralized p2p

1. Distinguish between centralized and decentralized P2P networks. 2. What are the advantages and disadvantages of a centralized P2P network? 3. What are the advantages and disadvantages of a decentralized P2P network? 4 ...

1 what is a boundary condition how do boundary conditions

1. What is a boundary condition? How do boundary conditions arise and how are they derived? 2. Summarize the boundary conditions for the general case of a boundary between two arbitrary media, indicating correspondingly ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen