Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Design and draw the ladder diagram circuit appropriate for a PLC that will fulfill the given control requirement:

A momentary push switch is to be recognized, remembered and employed to switch on an output for a period of 30 seconds.

After 30 seconds this output is to be switched off and should be off for 0.5 seconds before a second output switches on.

The second output remains on till a second push switch is operated to turn it off. If the second push is operated at any time then the current output should turn off and the system awaits the press of the first push. The rungs of ladder diagram should contain interlock contacts that prevent both outputs being on at similar time.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M910099

Have any Question? 


Related Questions in Electrical & Electronics

Question 1a for the circuit shown in figure 1 sketch the

Question 1. (a) For the circuit shown in FIGURE 1 sketch the voltage waveform across the secondary winding of the transformer. On the same diagram sketch the load voltage waveform. The sketches should take into account d ...

A module with 40 cells has an idealized rectangular i-v

A module with 40 cells has an idealized, rectangular I-V curve with I SC = 4 A and V OC = 20 V. If a single cell has a parallel resistance of 5Ω and negligible series resistance, draw the I-V curve if one cell is complet ...

1 explain the self-consistency condition for waveguiding in

1. Explain the self-consistency condition for waveguiding in a dielectric slab waveguide. 2. Discuss the dependence of the number of propagating modes in a dielectric slab waveguide on the ratio of the thickness d of the ...

An initially straight beam ab is bent into a circular arc

An initially straight beam AB is bent into a circular arc A'B' as shown in the figure. The deformation is specified as Where g(X 2 ) is a simple function of X 2 . (a) Find the deformation gradient in terms of g(X 2 ). (b ...

1 why is it necessary to have the minus sign associated

1. Why is it necessary to have the minus sign associated with the time rate of increase of magnetic flux on the right side of Faraday's law? 2. What is electromotive force? 3. What are the different ways in which an emf ...

1 describe the phenomenon of the bouncing back and forth of

1. Describe the phenomenon of the bouncing back and forth of transient waves on a transmission line excited by a constant voltage source in series with internal resistance and terminated by a resistance. 2. Discuss the v ...

1 what are the names of the protocols discussed in this

1. What are the names of the protocols, discussed in this chapter, that provide security for e-mail? 2. How does PGP create a set of security parameters? 3. What is the purpose of the Handshake Protocol in SSL? 4. What i ...

1 discuss how the superposition of two uniform plane waves

1. Discuss how the superposition of two uniform plane waves propagating at an angle to each other gives rise to a composite wave consisting of standing waves traveling bodily transverse to the standing waves. 2. What is ...

Suppose a geologist has collected 15 specimens of a certain

Suppose a geologist has collected 15 specimens of a certain rock, call it R1, and 10 specimens of... Suppose a geologist has collected 15 specimens of a certain rock, call it R1, and 10 specimens of another rock, call it ...

A voltage generator is connected to the input of a lossless

A voltage generator is connected to the input of a lossless line short-circuited at the far end. The frequency of the generator is varied and the line voltage and line current at the input terminals are monitored. It is ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen