Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

problem 1) During executing a program, when 8085 MPU completes fetching of machine code located at the memory address 2057H, prepare down the content of the program counter?

problem 2) What is the function of clock in Microprocessor?

problem 3) prepare down the difference between INR and INX instructions.

problem 4) prepare down the interrupt signals of 8085 microprocessor.

problem 5) prepare brief note on evolution of microprocessors.

problem 6) Describe the functions of the ALE and IO/M signals of 8085 microprocessor.

problem 7) Name the sequence of events which occurs when 8085 MPU reads from memory.

problem 8) If the 8085 adds 87H and 79H, state the contents of the accumulator and the status of the S, Z, and CY flags.

problem 9) If a clock frequency is 5 MHz, how much time is needed to execute the instruction of 18 T-states?

problem 10) Describe the programming model of 8085 μP with the help of appropriate diagram.

problem 11) Design and describe the timing diagram for opcode fetch operation.

problem 12) Describe different kinds of addressing modes of 8085.

problem 13) Describe why the number of output ports in the peripheral-mapped I/O is restricted to 256 ports.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M99209

Have any Question? 


Related Questions in Electrical & Electronics

For the euler beam element shown in the figure derive the

For the Euler beam element shown in the figure, derive the interpolation functions, N I (ξ), stiffness matrix, k, and nodal force vector, f. Assume that the uniformly distributed load is  f (x) = f. Note that the referen ...

Approximate using a number of terms of your choice through

Approximate (using a number of terms of your choice) through the three forms of Fourier series expansion the periodic signal that is depicted in the following figure Each time, a. Plot the approximate signal in time of t ...

Referring to the figure assume the flow to be frictionless

Referring to the figure, assume the flow to be frictionless in the siphon. Find the rate of discharge in cubic feet per second, and the pressure head at B if the pipe has a uniform diameter of 1 in. How long will it take ...

A create a vector of 5000 random numbers distributed

a. Create a vector of 5000 random numbers distributed according to the normal distribution with mean m = and variance s 2 = 3. b. Plot the histogram. c. Compute the mean value and the variance of the samples. d. Create a ...

1 a synchronous alternator is supplying 09 pu power to the

(1) A synchronous alternator is supplying 0.9 p.u. power to the grid when a temporary three-phase short occurs on the interconnector. The power angle curves are:- Pre-fault = 2.0 sin(delta) During fault = 0.5 sin(delta) ...

Consider a uniform bar with a cross-sectional area a 2

Consider a uniform bar with a cross-sectional area, A = 2 10 -4  m 2 , and a unit length, L = 1 m. The bar shows elastoplastic material behavior, as depicted in the figure. The plastic deformation starts at yield stress ...

1 what is a boundary condition how do boundary conditions

1. What is a boundary condition? How do boundary conditions arise and how are they derived? 2. Summarize the boundary conditions for the general case of a boundary between two arbitrary media, indicating correspondingly ...

1 considering te modes in a dielectric slab guide specify

1. Considering TE modes in a dielectric slab guide, specify the fundamental mode and discuss the associated cutoff condition. 2. Compare the phenomenon at cutoff in a metallic waveguide with that at cutoff in an optical ...

Instructions calculate the circuits by filling in all the

Instructions: Calculate the circuits by filling in all the blanks. 1. Et = 24 volts It = ______ amps Rt = ______ ohms 2. Et = 24 volts It = ______ amps Rt = ______ ohms 3. Et = 12 volts It = ______ amps Rt = ______ ohms ...

1 explain the term internal inductance2 what is meant by

1. Explain the term internal inductance. 2. What is meant by the quasistatic extension of the static field in a physical structure? 3. Outline the steps involved in the electroquasistatic field analysis of a parallel pla ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen