Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

1- Design a buck converter with the following specifications: Input voltage between 11 V and 15 V, output voltage 1.8 V, output current 20 A, inductor current ripple less than or equal to 2 A, output voltage ripple less than or equal to 0.018 V, switching frequency 100 kHz.

a) Find L, C such that the specifications are met over the whole input voltage range.

b) Verify your design using simulation.

c) Find the current and voltage ratings for the diode and the switch in this converter, then find an appropriate diode and MOSFET for this converter based on the ratings.

d) Suppose someone else has designed a buck converter for the specifications in this problem and chosen an inductor value of 47 μH and a capacitor value of 220 μF.

Determine what switching frequency is needed to meet the ripple specifications.

2- A buck converter has been designed for 5 V input, 1 V output, with an inductance of 10 ....and a switching frequency of 350 kHz.

a) Determine the load resistance and power for critical conduction mode.

b) Determine the duty ratio required to maintain a 1 V output as resistance increases by a factor of 10 from the critical conduction load.

c) Verify your results using simulations.

d) Sketch the curve of duty ratio vs. resistance for maintaining 1 V output voltage for R Œ [1,100] Ω.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M913973
  • Price:- $60

Priced at Now at $60, Verified Solution

Have any Question? 


Related Questions in Electrical & Electronics

You need to preare a project reportconstruct a digital

You need to preare a project report. Construct a digital radio transmit binary data over a distance of 15 cm. The digital radio circuit basically consisted of two main blocks: transmitter and a receiver. The transmitter ...

Find the disruptive and visual corona voltage of a grid

find the disruptive and visual corona voltage of a grid line operating at 132kv ,conductor diameter =1.9cm,conductor spacing =3.81m,temp=44,pressure=73.7,conductor surface factor ;fine weather=0.8;rough weather=0.66

1 discuss the general solutions for the line voltage and

1. Discuss the general solutions for the line voltage and current in time-domain and the notation associated with their representation in concise form. 2. What is the fundamental distinction between the occurrence of the ...

A circular loop antenna of radius 1 m in free space carries

A circular loop antenna of radius 1 m in free space carries a uniform current (a) Calculate the amplitude of the electric field intensity at a distance of 10 km in the plane of the loop. (b) Calculate the radiation resis ...

1 in internet telephony explain how a call from alice can

1. In Internet telephony, explain how a call from Alice can be directed to Bob when he could be either in his office or at home? 2. Do you think H.323 is actually the same as SIP? What are the differences? Make a compari ...

A clean 15--efficient module stc 1 m2 in size has its own

A clean, 15-%-efficient module (STC), 1 m 2 in size, has its own 90% effi- cient inverter. Its NOCT is 44° C and its rated power degrades by 0.5%/° C above the 25° C STC. a. What would its STC rated power be? b. Find the ...

Repeat problem with the elastic constants of the plastic

Repeat Problem with the elastic constants of the plastic defined as E = 10 GPa and ν = 0.485. Problem:- A rectangular plastic specimen of size 100 X 100 X 10 mm 3  is placed in a rectangular metal cavity. The dimensions ...

1 the dam shown below is 100 m wide determine the magnitude

1. The dam shown below is 100 m wide. Determine the magnitude and location of the force on the inclined surface. 2. The float in a toilet tank is a sphere of radius R and is made of a material with ρ. An upward buoyant f ...

Ohms law problemsquestion 1an alarm clock draws 05 a of

Ohm's Law Problems Question 1 An alarm clock draws 0.5 A of current when connected to a 120 volt circuit. Calculate its resistance. a) 150 ohms b) 120 ohms c) 60 ohms d) 240 ohms Question 2 If one 9 volt battery is used ...

Write the state equations for the systems depicted in fig

Write the state equations for the systems depicted in Fig. P10.5-1. Determine a new state vector w such that the resulting state equations are in diagonalized form. Write the output y in terms of w. Determine in each cas ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

WalMart Identification of theory and critical discussion

Drawing on the prescribed text and/or relevant academic literature, produce a paper which discusses the nature of group

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro