Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Electrical & Electronics Expert

Design a 2-digit 24 second 'shot-clock' countdown timer with pushbutton controller. The pushbutton controller will have one input: (IN) and provide two outputs: CNT and RST for count and reset respectively. At power on the counter will read 24 (RST). Whenever the pushbutton is pressed once the clock will start counting down (CNT). If the button is pressed a second time the clock must pause at the last number. Whenever the button is pressed a second time the count will resume. When the count reaches 0 a buzzer will sound (or LED light) for 3 seconds. To reset the clock the button should be pressed for at least 5 seconds. (Note: the clock must be able to be 'reset' even if the clock is counting or paused.)

Draw the whole system by using block diagrams. You might initially design the pushbutton state machine by using standard FSM notation, but you should eventually transform the state machine design into ASM notation, or just make the initial design by using ASM. Next implement and simulate the state machine by using both DEEDS Finite State Machine simulator and Multisim. Please describe proper operation of your state machine by using DEEDS d-MsFto me on the computer and give a written report of your design procedure and implementation of simulation.

Electrical & Electronics, Engineering

  • Category:- Electrical & Electronics
  • Reference No.:- M91030

Have any Question? 


Related Questions in Electrical & Electronics

1 what is a uniform plane wave2 why is the study of uniform

1. What is a uniform plane wave? 2. Why is the study of uniform plane waves important? 3. How is the surface current density vector defined? Distinguish it from the volume current density vector. 4. How do you find the c ...

Let xt be a signal whose fourier transform xomega is

Let x(t) be a signal whose Fourier transform X(ω) is nonzero only over 3 ≤ |ω| ≤ 9. Further, only frequencies 5 ≤ |ω| ≤ 7 contain useful information (the other frequencies can be considered to contain noise or different ...

1 in jpeg explain why we need to round the result of

1. In JPEG, explain why we need to round the result of division in the quantization step. 2. Explain why the combination of quantization/dequantization steps in JPEG is a lossy process even though we divide each element ...

1 in logisim implement an 8-to-1 mux using 2 4-to-1 muxes

1. In Logisim implement an 8-to-1 MUX using 2 4-to-1 MUXes and a 2-to-1 MUX. 2. In Logisim implement an 8-to-1 MUX using 4 2-to-1 MUXes and a 4-to-1 MUX. 3. In Logisim implement a circuit similar to the one in figure 8-1 ...

The grades of a group of 1000 students in an exam are

The grades of a group of 1000 students in an exam are normally distributed with a mean of 70 and a standard deviation of 10. A student from this group is selected randomly. a) Find the probability that his/her grade is g ...

1 at what point on the surface of the circular cylinder in

1. At what point on the surface of the circular cylinder in a potential flow does the pressure equal the free-stream pressure? 2. For the velocity potentials given below, find the stream function and sketch the streamlin ...

An infinite plane sheet lying in the plane carries a

An infinite plane sheet lying in the plane carries a current of uniform density Find the magnetic field intensities adjacent to the sheet and on either side of it. What is the polarization of the field?

Consider a uniform bar with a cross-sectional area a 2

Consider a uniform bar with a cross-sectional area, A = 2 10 -4  m 2 , and a unit length, L = 1 m. The bar shows elastoplastic material behavior, as depicted in the figure. The plastic deformation starts at yield stress ...

1 discuss the consequence of the frequency dependence of

1. Discuss the consequence of the frequency dependence of the phase velocity of a wave in a material medium. 2. What is loss tangent? Discuss its significance. 3. What is the intrinsic impedance of a material medium? Wha ...

1 describe the phasor technique of solving a differential

1. Describe the phasor technique of solving a differential equation for the sinusoidal steady-state solution. 2. State Coulomb's law. To what law in mechanics is Coulomb's law analogous? 3. What is the definition of the ...

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen