Ask Question, Ask an Expert

+1-415-315-9853

info@mywordsolution.com

Ask Mechanical Engineering Expert

problem 1:

a) Describe open loop and closed loop control system with some exs.
b) describe the control system of hydro thermal power plant with neat block diagram.

problem 2: prepare detailed notes on:

a) Feed water control in boilers.                       
b) Steam temperature control in boilers.               
c) Furnace pressure control in boilers.

problem 3: Describe with details pulverizer control, draft control and combustion control in boilers.

problem 4: describe in detail about the control system which is used in cogeneration plant.

problem 5: Describe in detail about:

a) Governor over speed cut off.                   
b) PLC applications.

problem 6: Describe the boiler components assembly with appropriate sketch.

problem 7:

a) Describe microprocessor based temperature control system in steam power plant.
b) Distinguish between analog and digital instruments.       
c) Illustrate the limitations of analog instruments and the merits of digital instruments.

problem 8:

a) Describe the IEEE 488 standard interface.               
b) describe the distributed data acquisition and control system.

problem 9: With a neat sketch describe the different components of nuclear power plant and its essential controls.

problem 10: Describe in detail the Computer Automated Measurement and Control (CAMAC) standards.

Mechanical Engineering, Engineering

  • Category:- Mechanical Engineering
  • Reference No.:- M93152

Have any Question? 


Related Questions in Mechanical Engineering

What primary factors determine the number of load cycles

What primary factors determine the number of load cycles required to break a bolt subject to fatigue loading? Describe the appearance of the break surface of a bolt which has failed in fatigue ? Where on a bolt are you m ...

The demand for a certain product is a linear function of

The demand for a certain product is a linear function of the price. The sales of the product for three different prices are given in the following table Find the least squares regression line and estimate the demand when ...

Let the texturized si floating gate be modeled by

Let the texturized Si floating gate be modeled by semi-spherical hills. Calculate the radius of the hemisphere that would increase the write/erase time by 100 over the flat poly-Si/SiO2 interface. Use the Fowler-Nordheim ...

Assignmentin mse 2010 we talk about several general classes

Assignment In MSE 2010 we talk about several general classes of materials: metals, polymers, ceramics, glasses and composites. We know that these are just the basic categories and we've discussed several specific example ...

1 by how much will the clamping force on the joint be

1. By how much will the clamping force on the joint be reduced? Sketch the new joint diagram, assuming maximum initial preload? Compute the estimated maximum bolt tension and minimum clamping force under the 3,000 lbs ex ...

1 a cylindrical pressure vessel with hemispherical endcaps

1. A cylindrical pressure vessel with hemispherical endcaps has radius r = 2 m, wall thickness t = 10 mm, and is made of steel with yield stress σy = 1800 MPa. It is internally pressurized at p = 2 MPa. Compare the Tresc ...

A watertight bulkhead 22 ft high forms a temporary dam for

A watertight bulkhead 22 ft high forms a temporary dam for some construction work. The top 12 ft behind the bulkhead consists of sea water with a density of 2 slugs/ft 3  , but the bottom 10 ft begin a mixture of mud and ...

The maximum theoretical efficiency of an internal

The maximum theoretical efficiency of an internal combustion engine is achieved in a reversible Carnot cycle. Assume that the engine is operating in the Otto cycle and that = 5R/2 for the fuel-air mixture initially at 27 ...

Engineering skills project brief flume Engineering Skills Project Brief: Flume Ride

Engineering Skills Project Brief: Flume Ride Introduction Employers are constantly asking for engineering graduates who have good team skills, are problem solvers and are good communicators. On top of that, engineers nee ...

Use castiglianos second theorem to determine the tip

Use Castigliano's second theorem to determine the tip deflection of this cantilever with a length L, a constant E I, and a linearly increasing load with a maximum force/length q0. Confirm your result using Table 9.1.

  • 4,153,160 Questions Asked
  • 13,132 Experts
  • 2,558,936 Questions Answered

Ask Experts for help!!

Looking for Assignment Help?

Start excelling in your Courses, Get help with Assignment

Write us your full requirement for evaluation and you will receive response within 20 minutes turnaround time.

Ask Now Help with Problems, Get a Best Answer

Section onea in an atwood machine suppose two objects of

SECTION ONE (a) In an Atwood Machine, suppose two objects of unequal mass are hung vertically over a frictionless

Part 1you work in hr for a company that operates a factory

Part 1: You work in HR for a company that operates a factory manufacturing fiberglass. There are several hundred empl

Details on advanced accounting paperthis paper is intended

DETAILS ON ADVANCED ACCOUNTING PAPER This paper is intended for students to apply the theoretical knowledge around ac

Create a provider database and related reports and queries

Create a provider database and related reports and queries to capture contact information for potential PC component pro

Describe what you learned about the impact of economic

Describe what you learned about the impact of economic, social, and demographic trends affecting the US labor environmen